Contact Us

LT8610AIMSE-5#TRPBF

Brand: Analog Devices
Analog Devices LT8610AIMSE-5#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT8610AIMSE-5#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT8610AIMSE-5#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT8610AIMSE-5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT8610AIMSE-5#TRPBF: the fixed 5 V option with no divider

LT8610AIMSE-5#TRPBF is the industrial release of the 3.5 A LT8610A with the output fixed at 5 V. The suffix removes the feedback divider: the output pin is the feedback node, the reference is trimmed inside the part, and the published output window is 4.94 V to 5.06 V. That is 120 mV, or 1.2 percent, which no two resistor divider of ordinary tolerance is going to beat.

Published values

ParameterValue
Output5 V fixed, 4.94 V to 5.06 V over temperature
Input voltage3.4 V to 42 V
Continuous output3.5 A
Top switch current limit5 A minimum, 6.7 A typical, 8 A maximum
Bottom switch current limit3.4 A minimum, 4.3 A typical
Minimum on time30 ns
Switching frequency200 kHz to 2.2 MHz
Efficiency95 percent at 1 A, 5 V out from 12 V
Quiescent current2.5 uA
Power good windowplus or minus 9 percent, 450 mV at 5 V
Thermal resistance40 C/W junction to ambient
Fixed output siblings3.3 V version in the same family
GradeI, guaranteed over -40 to 125 C
Package16-lead MSOP, VOUT on pin 16 in place of FB

What the fixed output removes

A divider of two 1 percent resistors adds about 1.4 percent at the midpoint, which is more than the reference contributes on its own. The fixed part publishes 1.2 percent total, and the divider current, 25 uA through a 100 kohm pair, is gone as well.

The pinout changes: pin 16 becomes VOUT instead of FB. That is not a detail to discover at assembly. An adjustable board cannot take the fixed part without a trace change, and a fixed board cannot take the adjustable part at all.

The 30 ns floor makes 2.2 MHz usable into 3.3 V

42 V to 3.3 V is 7.86 percent duty, which is 35.7 ns at 2.2 MHz. Against a 30 ns minimum that clears with 5.7 ns of margin, where the 50 ns part of the same family would have to drop to 1.571 MHz. The faster edge is why the A series exists.

At 2.2 MHz the 30 ns floor is 6.6 percent of the period, so even a 40 V rail into 3.3 V keeps 1.3 points of headroom. That matters on a 5 V rail only if it is stacked on a 3.3 V pre regulator; on a straight 12 V to 5 V rail the floor is never reached.

3.5 A against a 5 A minimum switch limit

The top switch limit is 5 A minimum against a 3.5 A continuous rating, which is 1.5 A of margin. The bottom limit is 3.4 A minimum, which is below the rating, so the inductor peak rather than the top switch is the constraint in a hard transient.

The family also states that it tolerates inductor saturation in overload, which is the honest way of saying that the loop will current limit rather than run away when the core saturates. That is a behaviour to verify on the bench, not a reason to choose an inductor with a saturation point at the load current.

Buyers usually arrive at the power management cross reference to find the family alternatives, then use the pin to pin cross reference to confirm a substitute before it is fitted; one stop BOM sourcing is the routine for a part that has already stopped shipping.

Two questions buyers ask

Can the fixed 5 V part be used at 3.3 V? No. The output is trimmed inside the part and pin 16 is the output sense, so there is no divider to change. The 3.3 V option is a separate order code.

Is the fixed version more accurate than a divider? Yes, on paper: 1.2 percent total against about 1.4 percent from a pair of 1 percent resistors plus the reference. It also removes the divider current from the standby budget.