LT3684IDD#TRPBF
Product Specifications
LT3684IDD#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3684IDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3684IDD: A 2 A, 34 V Buck With a 0.18 Ohm Switch and a Cold Guarantee
The LT3684 is the 2 A member of the 36 V buck family: 3.6 V to 34 V operating with a 36 V absolute maximum, a 0.18 Ohm switch, a 1.265 V feedback reference and a 300 kHz to 2.8 MHz oscillator. The I grade is guaranteed over minus 40 C to 125 C junction, and that is the meaningful difference from the E grade in the same family, which stops at 85 C ambient. This order code is the 3 by 3 mm DFN with the exposed pad on pin 11.
Published values
| Parameter | Value |
|---|---|
| Input range | 3.6 V to 34 V operating, 36 V absolute maximum |
| Output current | 2 A maximum |
| Switch resistance | 0.18 Ohm, 360 mV at 2 A |
| Switch current limit | 3.1 A minimum, 3.6 A typical, 4.0 A maximum |
| Feedback reference | 1.265 V, 1.240 to 1.290 V |
| Output range | 1.265 V to 20 V |
| Switching frequency | 300 kHz to 2.8 MHz |
| Minimum off time | 100 ns typical, 150 ns maximum |
| Power good offset | 100 mV below the feedback point, 1.165 V |
| Quiescent current | 0.4 mA typical, 0.8 mA maximum with the bias pin at 3 V |
| Package | 10 lead 3 by 3 mm DFN, exposed pad on pin 11 |
| Thermal resistance | 45 C/W junction to ambient |
| Guarantee | I grade, minus 40 C to 125 C junction, tested |
0.18 Ohm is 0.72 W at 2 A, and the limit is only 3.1 A minimum
The switch dissipates 0.72 W at the full 2 A, which at 45 C/W is 32 C of rise, so a 90 C ambient puts the junction at 122 C and the load has to come down above that. The tighter constraint is the current limit: 3.1 A minimum against a 2 A rating leaves 1.1 A peak to peak of ripple, 55 percent, and at 34 V input the ripple is at its largest because the off time is longest. An inductor chosen for a 12 V input will have more ripple at 34 V than the limit allows, and the failure looks like a converter that folds back only at high line.
The 0.18 Ohm switch is also why this part runs hotter than the 95 mOhm part next to it in the family, and why the 2 A rating is not a 3.5 A rating with a different label: the die is different, the limit is lower and the ripple budget is smaller.
The I grade is what separates this from the E grade
The E grade in this family operates from minus 40 C to 85 C and is guaranteed from 0 C to 85 C, so its junction ceiling is effectively 85 C ambient plus whatever the thermal rise allows. The I grade is guaranteed to a 125 C junction, which is what a 2 A buck in a sealed enclosure needs. That difference is not a temperature range on paper: it is the difference between a part that can be used at a 90 C ambient and one that cannot be used above 70 C.
The 2.8 MHz top of the oscillator range is also where the I grade matters least and the thermal matters most. At 2.8 MHz the switching losses rise and the on time for a 34 V to 3.3 V conversion is 34.7 ns, while the minimum off time is 100 ns typical and 150 ns maximum. At 1 MHz the off time is 903 ns and the build is comfortable, so the frequency choice is a trade between inductor size and both switching loss and minimum on time.
Power good at 1.165 V, which is 92.1 percent, not 90
The comparator trips 100 mV below the 1.265 V feedback point, so the flag asserts at 1.165 V, which is 92.1 percent of the regulated output; the front page describes it as 90 percent. On a 5 V rail that is 4.61 V, and on a 12 V rail 11.05 V. The output is set by a divider from 1.265 V, so the 10 mV of hysteresis is 0.8 percent of the reference and produces a single clean edge on a slow ramp rather than a burst.
The flag is an open collector with a 300 uA sink capability, so it drives a logic input or a small opto, and its pull up should come from a rail that is present before this converter starts, otherwise the flag is dead until the output is up and the sequencing logic never sees it.
When an order code in this family cannot be found, the power management cross reference lists what else does the same job, vendor consolidation covers what to check before a part is dropped into an existing board, and the obsolete part cross reference hub is the route we take on a live shortage.
Two questions buyers ask
Is 34 V enough for a 24 V automotive rail? The operating range is 3.6 V to 34 V with a 36 V absolute maximum, so a nominal 24 V system with load dump is outside the part unless the transients are clamped upstream. A 24 V rail at plus 10 percent is 26.4 V, which is inside; a load dump is not.
Why does this part draw 850 uA at no load? It has no burst mode, so it switches continuously and the quiescent current is the operating current, 0.4 mA typical and 0.8 mA maximum with the bias pin at 3 V. A battery product that sleeps needs the burst mode sibling in the same family, which draws 75 uA instead.