Contact Us

LT3094EDD#TRPBF

Brand: Analog Devices
Analog Devices LT3094EDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3094EDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3094EDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3094EDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3094EDD#TRPBF: extended grade negative regulator, 3 mm DFN

The LT3094EDD#TRPBF is the extended grade of the 500 mA negative regulator in the 3 mm by 3 mm 12-lead DFN, tape and reel, rated -40 C to 125 C. It carries the same table as the rest of the family, from -1.8 V to -20 V input and 0 V to -19.5 V output through 235 mV dropout and 0.8 uV RMS noise to 74 dB rejection at 1 MHz. The DFN body gives 33 C/W junction to ambient and 8 C/W junction to case, and the exposed pad is connected to IN.

Published values

ParameterValue
Input voltage-1.8 V to -20 V
Output voltage0 V to -19.5 V, set by one resistor
Output current500 mA
Dropout voltage235 mV typical
Output noise0.8 uV RMS, 10 Hz to 100 kHz
Spot noise2.2 nV per root hertz at 10 kHz
Supply rejection74 dB at 1 MHz
SET pin current100 uA, 1 percent
Quiescent current2.35 mA, 3 uA shutdown
Output capacitor10 uF ceramic minimum
Package and grade3 mm by 3 mm DFN, -40 C to 125 C, tape and reel

The tracking pin in a two stage rail

Most negative rails are made in two steps, a switcher that creates a raw negative voltage and a linear stage that cleans it. The LT3094 has a tracking function for exactly that arrangement: the VIOC pin drives the upstream regulator so that the voltage across the linear stage stays inside a narrow window. The benefit is double. The dissipation in the DFN stays low even when the raw rail is much larger than the output, and the rejection stays high because the regulator keeps its headroom instead of running into dropout. For a buyer the tracking pin is also a documentation question, since the upstream converter has to accept the control signal, and a substitute regulator without that pin changes the thermal calculation on the board.

Fast start-up and power good

The part has a programmable power good output and a fast start-up path. In a system that brings up a positive and a negative rail together, power good is what tells the controller that the negative rail is valid, and the start-up speed decides how long the amplifier sits with an undefined supply. The SET pin capacitor that filters the reference also sets the start-up ramp, so there is a real trade between noise and speed. A buyer should not accept a substitute that quotes the same noise with a much larger reference capacitor unless the start-up requirement is rechecked, because the capacitor on SET is part of both figures.

Thermal budget at 500 mA

With 33 C/W junction to ambient on a four layer board with a reasonable copper shape, a 1 W dissipation raises the junction about 33 C above the local board temperature, which is workable. At 2 W the same copper gives 66 C and the margin depends entirely on the ambient inside the enclosure. The 8 C/W junction to case is the number that matters when the board is bolted to a metal chassis, because heat then leaves through the pad and the chassis rather than through the air. Assembly houses that have never run this body should be reminded that the pad is IN, so the copper under the part must be isolated from the ground pour.

Ordering notes

The E grade covers most commercial instrument work and is the version usually quoted first. H and MP versions of the same DFN cover -40 C to 150 C and -55 C to 150 C, and they are the right choice for downhole, automotive underhood or avionics bays where the local ambient is above 100 C. The TR suffix is tape and reel; the 500 unit reel is available as TRMPBF through some channels. For files that mix this rail with the rest of the ADI and Linear power families, the power management cross reference keeps the codes together, the shortage recovery page covers what to do when the reel is not on the shelf, and the vendor consolidation page explains how several ADI lines are grouped on one purchase order.