Contact Us

LT3092IDD#TRPBF

Brand: Analog Devices
Analog Devices LT3092IDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3092IDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3092IDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3092IDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3092IDD#TRPBF: 200 mA current source in a 3 mm DFN

The LT3092IDD#TRPBF puts the two terminal current source into the 8-lead 3 mm by 3 mm DFN, industrial grade, tape and reel. The electrical behaviour is the same as the SOT-23 and SOT-223 bodies: 10 uA SET pin reference at 1 percent, 1.2 V to 40 V input, 0.5 mA to 200 mA output from two resistors, better than 10 ppm per volt of current regulation, no capacitors needed and reverse voltage plus reverse current protection. What changes is the thermal path, which is the reason this body exists at the top of the current range.

Published values

ParameterValue
Input voltage range1.2 V to 40 V
Output current0.5 mA to 200 mA
SET pin current10 uA, 1 percent
Current regulationbetter than 10 ppm per volt
Capacitorsnone required
Protectionreverse voltage, reverse current, current limit, thermal shutdown
Package8-lead 3 mm by 3 mm DFN
Temperature range-40 C to 125 C
Packingtape and reel

Dissipation decides the body, not the current

A current source at 200 mA dissipates the voltage across it times the current, and that product is the whole thermal story. In a 5 V to 3.3 V loop the device carries 1.7 V, which is 0.34 W at full current and comfortable in any of the three bodies. In a 24 V loop feeding a 5 V load the same current puts 19 V across the device, which is 3.8 W and needs the DFN with its exposed pad on copper, and even then only with a derated current. This is why a sourcing file should never carry the current rating alone. The DFN's pad is the thermal path, so a substitute in a SOT-23 body that is offered as equivalent on current will not hold the same dissipation.

Where the compliance voltage is measured

The device needs 1.2 V across it to regulate, and that headroom is in series with the load. In a two terminal floating arrangement the total loop voltage has to cover the load plus 1.2 V plus the drop in the wiring, and in a long cable the wiring drop can be several volts. The regulator cannot distinguish cable resistance from load resistance, so it simply raises its own voltage to hold the current, which moves the dissipation into the device. Systems that run a current loop over hundreds of metres usually discover this after the first thermal shutdown, so the calculation belongs in the specification rather than in the field.

The offset and the SET pin

The SET pin current of 10 uA flows through the external resistor network, so leakage at that node becomes an error term. On a four layer board with a DFN body, flux residue and humidity are the usual sources of leakage, and a 10 uA reference tolerates very little of it. Cleaning and conformal coat decisions therefore belong to the same review as the resistor tolerance. This is one place where the smaller body can help, since the pad geometry and the shorter path to the SET pin give less opportunity for contamination to bridge the node to a neighbouring net.

Buying the DFN code

The IDD code is industrial grade at -40 C to 125 C and is stocked mainly for builds that need the thermal path. Automotive qualified versions of the family carry the W suffix and are listed separately. For files that mix this part with other ADI power codes, the power management cross reference keeps the bodies and grades apart, the BOM shortage page covers what happens when the DFN is not available, and the vendor consolidation page explains grouping several ADI lines on one order.