Contact Us

LT3092ETS8#TRPBF

Brand: Analog Devices
Analog Devices LT3092ETS8#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3092ETS8#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3092ETS8#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3092ETS8#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3092ETS8#TRPBF: extended grade current source for in-line limiting

The LT3092ETS8#TRPBF is the extended grade of the 200 mA two terminal current source in the 8-lead SOT-23, tape and reel, rated -40 C to 125 C. It carries the 10 uA SET pin reference with 1 percent initial accuracy over that window, a 1.2 V to 40 V input range, an output current from 0.5 mA to 200 mA set by two resistors, current regulation better than 10 ppm per volt, and no requirement for input or output capacitance. The E and I versions of this body share the electrical table, so the choice between them is a documentation and screening one.

Published values

ParameterValue
Input voltage range1.2 V to 40 V
Output current0.5 mA to 200 mA
SET pin current10 uA, 1 percent initial accuracy
Current regulationbetter than 10 ppm per volt
Line regulation0.001 percent per volt typical
Capacitorsnone required at input or output
Reverse protectionreverse voltage and reverse current
Protectioncurrent limit and thermal shutdown
Package8-lead SOT-23, tape and reel
Temperature range-40 C to 125 C, extended grade

In-line limiting in a field wiring loop

An in-line limiter sits in series with a signal or a supply and caps the current that can flow if the far end shorts. The LT3092 does that without a sense resistor in the conventional sense, because the SET network sets the limit directly, and the part does not need a capacitor on either side. In a loop that runs outdoors the absence of capacitance is a practical advantage: there is no stored energy to discharge into a fault, and no capacitor to age. The 40 V input range covers most 24 V industrial loops with margin for transients that the front end clamp does not catch.

Intrinsic safety circuits

The data sheet names intrinsic safety as an application, and the reason is the same property. A source that limits current and holds high impedance at AC does not need the barrier to store energy, so the assessment is simpler. The device also withstands reverse voltage and reverse current, which is what happens when a loop is wired backwards during commissioning. Buyers building for hazardous areas should note that the qualification of the complete barrier is a system matter, and the regulator only supplies one of the limits.

Temperature and drift over a long life

The extended grade covers -40 C to 125 C, and the SET pin reference has a low temperature coefficient, so the current stays within its band across that window. In a product with a ten year life the resistors are the parts that move, and the data sheet's 1 percent initial accuracy figure is the starting point rather than the end. A drift complaint on a current loop is usually traceable to the resistor pair or to leakage at the SET node, and the regulator is rarely the cause.

Ordering and substitution

ETS8 and ITS8 share a body and a table, so a line short of one grade can usually take the other without requalification. Moving to the DFN or SOT-223 body changes the thermal path and needs a board change. Automotive versions carry the W suffix and are listed separately in the order table. For files that carry this device alongside other ADI parts, the power management cross reference groups the codes, the ADI second source notes set out what a substitute must match on reference accuracy and compliance, and the cost page covers the levers on a high volume build.