Contact Us

LT3092EST#TRPBF

Brand: Analog Devices
Analog Devices LT3092EST#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3092EST#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3092EST#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3092EST#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3092EST: the E grade current source and who should not buy it

The LT3092EST is the E grade of the two-terminal programmable current source in a 3-lead SOT-223, and it is the same silicon as the industrial and the high reliability grades: 0.5 mA to 200 mA set by two resistors, 1.2 V to 40 V input, a 10 microamp set pin with 1 percent initial accuracy, no input or output capacitor needed for stability, reverse voltage and reverse current protection, and thermal shutdown. The order table puts the E and the I grade in the same minus 40 to 125 degree junction range. The MP grade reaches minus 55. What separates the three is the guarantee.

Published values

ParameterValue
Output current0.5 mA to 200 mA
Input voltage1.2 V to 40 V
Set pin current10 microamps, 1 percent initial accuracy
Set pin accuracy over temperature9.8 to 10.2 microamps
Dropout voltage1.22 V typical, 1.45 V maximum at 10 mA
Minimum load currentabout 300 microamps, the quiescent current of the part
Current limit200 mA minimum, 300 mA typical
Ripple rejection90 dB at 120 Hz, 75 dB at 10 kHz, 20 dB at 1 MHz
Thermal regulation0.003 percent per watt on a 10 millisecond pulse
Package3-lead SOT-223
Temperature gradeE, junction from minus 40 to 125 degrees
QualificationAEC-Q100 for automotive applications

The three grades and what actually differs

The E and I grades share a minus 40 to 125 degree junction range in the order table, and the MP grade extends the cold end to minus 55. Between the E and the I the difference is in how the limits are guaranteed: the E is tested at 25 degrees with the rest assured by characterisation, and the I is guaranteed over the full range. The MP is tested and guaranteed over minus 55 to 125.

For a current source driving a sensor in a product that is validated as a system, the E grade is the correct and cheapest choice. For a circuit whose error budget quotes the set pin accuracy at both temperature extremes, the I grade is the one whose numbers can be put in the report. The electrical behaviour on the bench at room temperature is identical, which is why the wrong grade is usually discovered in a qualification review rather than in a prototype.

Setting 50 milliamps and knowing what the error will be

For 50 mA the ratio of RSET to ROUT is 5000. With RSET at 20 kilohm and ROUT at 4 ohm, the voltage across RSET is 200 millivolts and the 2 millivolt offset between the SET and OUT pins is a 1 percent term, which adds to the 1 percent initial accuracy of the set current. The two together are the error budget, and a 0.1 percent resistor pair does not improve either of them.

At the low end the arithmetic changes. A 0.5 mA source with RSET at 20 kilohm needs an ROUT of 400 ohm, which is comfortable. A 0.5 mA source with RSET at 2 kilohm needs 40 ohm, and now the offset is 10 percent of the reference and the accuracy is gone. The minimum current in the table is achieved with a large RSET, not with a small one, and that is the opposite of what a scaled down version of the 50 mA circuit would give.

Thermal regulation is the spec that decides a precision loop

Thermal regulation of 0.003 percent per watt means that a watt of change in dissipation moves the set current by 30 parts per million. In a 40 V loop running at 20 mA the dissipation is 0.8 W, and the change between a cold start and a warm board can be a substantial fraction of that, so the current moves by tens of parts per million for thermal reasons alone. That is fine for a sensor excitation and not fine for a calibration reference.

The cure is to keep the voltage across the part constant, which is a heat problem rather than an electrical one: a series resistor or a pre-regulator that absorbs the variable part of the input keeps the dissipation steady, and steady dissipation is what a precision current source needs. It costs a resistor and it removes the largest error term in the loop.

Sourcing notes for this family: the power management cross reference holds the cross references, the ADI second source page is the pre substitution check, and OEM procurement is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Is the E grade the same die as the I grade? The electrical core is the same and the order table gives both the same junction range. The difference is that the I grade is guaranteed over the full range while the E grade is tested at 25 degrees with the rest assured by characterisation.

What is the minimum current the part can regulate? 0.5 mA, and it is reached with a large RSET. Because the set pin current must stay at 10 microamps, the minimum load current is about the quiescent current of the part, which is roughly 300 microamps at the low end.