Contact Us

LT3090IDD#TRPBF

Brand: Analog Devices
Analog Devices LT3090IDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3090IDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3090IDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3090IDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3090IDD#TRPBF: the 10-lead DFN body with IN on the exposed pad

The LT3090IDD#TRPBF is the industrial grade of the 600 mA negative regulator in the 10-lead 3 mm by 3 mm DFN, supplied in tape and reel. It carries the same electrical table as the MSOP: -1.5 V to -36 V input, 0 V to -32 V output, 50 uA SET pin, 300 mV dropout at 600 mA, 18 uV RMS noise and 85 dB rejection at 120 Hz. The DFN brings the junction to case figure to 8 C/W and the junction to ambient figure to 33 C/W, and it moves the heat path from the leads to the exposed pad, which on this part is the IN pin.

Published values

ParameterValue
Input voltage-1.5 V to -36 V
Output voltage0 V to -32 V
Output current600 mA
Dropout voltage300 mV typical at 600 mA
SET pin current50 uA, 49 to 51 uA over temperature
GND pin current1 mA at no load, 11.5 mA at 600 mA
Output noise18 uV RMS, 10 Hz to 100 kHz
Thermal resistance33 C/W junction to ambient, 8 C/W to case
Package10-lead, 3 mm by 3 mm DFN, exposed pad is IN (pin 13)
Grade-40 C to 125 C, tape and reel

The pad is a live negative node

Nearly every DFN on a mixed-signal board has its exposed pad on ground, and assembly houses treat the pad as a ground connection by habit. On the LT3090 the pad is IN, so the copper under the body sits at the negative input and must be isolated from any ground pour. The failure mode is not subtle: a pour that creeps under the part creates a short from the negative input to ground through the thermal vias. The correct arrangement is a dedicated copper shape on the component side, connected to the input capacitor and to the upstream converter, with the ground plane kept on the other layers and no thermal vias into it inside the pad outline.

What 8 C/W to case changes

With the pad soldered to a copper shape, heat leaves through the bottom of the package at 8 C/W rather than through the air at 33 C/W. For a 1 W dissipation that is the difference between a 33 C and an 8 C rise from junction to the copper, and the copper itself then has to shed that heat to the board and the air. In practice the 3 mm body with a 2500 square millimetre copper shape settles close to the published 33 C/W end to end, but a board with heavy copper on the back side and vias outside the pad outline can do better. A buyer looking at a thermal problem on this part should ask for the copper area on both sides, not just the package.

Current limit and monitoring in a small body

Both the current limit and the current monitor survive the shrink from MSOP to DFN. The ILIM pin takes a resistor to ground and sets the point at which the regulator folds back, which lets a system protect a connector or a cable rather than only the regulator. The IMONP and IMONN pins give a scaled copy of the load current on the positive and negative side, and because the rail is below ground the two pins let a single positive-referenced ADC read the current without a level shift. For a data acquisition front end that already has a multiplexer, that removes an isolated amplifier from the parts list.

Order code and supply note

The TRPBF suffix is the taped reel; the same body in tray form is IDD#PBF and the extended grade is EDD#TRPBF. All three share the die and the pinout, so a reel quantity can be split with the tray part when a build is small. Buyers moving a board from the MSOP to the DFN should confirm the pad connection on the assembly drawing before the first build, because that is the one change that can cost a panel. The power management cross reference lists the negative families side by side, vendor consolidation covers putting the ADI rails on one schedule, and the one stop BOM page covers mixed orders.