Contact Us

LT3088HST#TRPBF

Brand: Analog Devices
Analog Devices LT3088HST#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3088HST#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3088HST#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3088HST#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3088HST#TRPBF: 150 C junction headroom in a SOT-223

The LT3088HST#TRPBF is the H grade of the 800 mA regulator in the 3-lead SOT-223, tape and reel, specified from -40 C to 150 C. It keeps the family electrical table: 1.2 V to 36 V input, 0 V to 34.5 V output from one SET resistor, 50 uA reference at 1 percent, 27 uV RMS noise, under 1 mV of load regulation that is independent of output voltage, and 0.001 percent per volt of line regulation. The H grade exists for boards where the local ambient inside the enclosure sits above 85 C and the junction has to be allowed to run hotter than an industrial part permits.

Published values

ParameterValue
Input voltage1.2 V to 36 V
Output voltage0 V to 34.5 V
Output current800 mA
SET pin current50 uA, 1 percent
Output noise27 uV RMS
Load regulationunder 1 mV typical
Input and output capacitorsstable with or without
Protectionreverse battery, reverse current, current limit, thermal limit
Package3-lead SOT-223, tape and reel
Temperature range-40 C to 150 C, H grade

The 150 C window is about derating, not about running hot

A grade specified to 150 C does not mean the board should operate at 150 C. It means the guaranteed limits hold across that span, so a junction that reaches 130 C on a hot day inside a sealed box is still inside the specification instead of outside it. Electrical parameters drift over that span, and the reference current is the one that matters here, because it sets the output. A 150 C grade part holds its band across a wider range, which is why it is chosen for equipment mounted in cabinets with no forced air, for power supplies inside machine tools, and for products that must keep working while a fan has failed.

Thermal calculation in a SOT-223

The tab of the SOT-223 is the output on this device, so the copper under the tab is the regulated rail. A square centimetre of copper on the tab side and a similar area on the opposite layer, stitched with vias, is what makes the thermal resistance usable. At 800 mA with 2 V across the part the dissipation is 1.6 W, and the junction rise over ambient depends on that copper and on the air movement. In a box with no airflow the rise can be 60 to 80 C, which is exactly the case the H grade covers and the industrial grade does not. A buyer specifying this code should ask for the board's measured ambient rather than an assumed one.

Extended safe operating area

The family is built with an extended safe operating area, so the pass transistor tolerates a large voltage across it while carrying current, which is what allows a 24 V to 3.3 V drop at a few hundred milliamps without a second stage. Even so, the package sets the ceiling. The DD-Pak body of the same device carries more copper and is the practical answer when the drop is large and the current is at the top of the range.

Ordering

HST is the H grade in SOT-223 with tape and reel. The same grade exists in DD-Pak and in the 8-lead DFN, and moving between bodies does not change the electrical table but does change the copper. Buyers meeting this code during a board revision should check whether the existing footprint is the SOT-223 or the DD-Pak, because the two are not interchangeable without a board change. Our power management cross reference lists the bodies against the grades, the BOM shortage page covers the options when the H grade is not in stock, and the vendor consolidation page explains grouping this line with other ADI parts.