Contact Us

LT3086IFE#TRPBF

Brand: Analog Devices
Analog Devices LT3086IFE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3086IFE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3086IFE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3086IFE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3086IFE#TRPBF: current and temperature telemetry on a 2.1 A rail

The LT3086IFE#TRPBF is the industrial grade of the 40 V, 2.1 A regulator in the 16-lead TSSOP, on tape and reel and rated -40 C to 125 C at the junction. It regulates 0.4 V to 32 V from a single resistor on the SET pin, accepts 1.4 V to 40 V on the input, and holds plus or minus 2 percent over line, load and temperature. What puts this part ahead of a plain regulator is the telemetry: an output current monitor, a temperature monitor with a programmable thermal limit, a power good flag with a programmable threshold and a cable drop compensation pin.

Published values

ParameterValue
Input voltage1.4 V to 40 V
Output voltage0.4 V to 32 V
Output current2.1 A
Dropout voltage330 mV typical at 2.1 A
Reference400 mV, SET pin current 50 uA
Current monitorIMON equals load current divided by 1000
Power good threshold0.4 V on the RPWRGD pin
Minimum output capacitor10 uF ceramic
Output noise40 uV RMS, 10 Hz to 100 kHz
Thermal resistance25 C/W on 2500 square millimetres of copper
Package and grade16-lead TSSOP, -40 C to 125 C, tape and reel

Turning the monitor into a voltage

The IMON pin delivers one thousandth of the load current, so the value of the resistor to ground sets the scale. With 330 Ohm the pin sits at 0.33 V for 1 A and 0.693 V for the full 2.1 A, which is a comfortable range for a 3.3 V ADC input and leaves headroom for a fault. With 1 kOhm the same currents give 1 V and 2.1 V, which suits a 5 V system. The resistor value also interacts with the current limit function when IMON is tied to ILIM, which is how the external limit is set: the current limit trips when the ILIM pin reaches 0.8 V, so the resistor ratio, not the absolute value, defines the point.

Temperature as a measured quantity

The TEMP pin outputs a voltage that tracks the junction, roughly 1.22 V at 25 C and falling at a published rate as the die heats, and the ITEMP pin sets the current at which the part begins to fold back. That gives a system two options: use the analog output to log the thermal history of the board, or set the foldback point below the internal shutdown so the rail sags gradually instead of disappearing. For equipment that runs in an enclosure with no fan, the second option is usually the difference between a graceful degradation and a hard reset of the whole instrument.

Transient behaviour at 2.1 A

A 2.1 A step with 10 uF of ceramic output moves the rail by a few tens of millivolts before the loop recovers, and the power good flag is deliberately slow: the RPWRGD reference has 15 to 35 uA of hysteresis current and a built in delay, so a short dip during a load step does not toggle the flag. That matters when the flag drives a sequencer, because a spurious drop would restart the downstream converters. If a shorter delay is needed for a fault case, the delay capacitor on the CPGSET pin sets it, and a value above 270 pF filters noise on the threshold.

Order code and stock

IFE is the industrial TSSOP on tape and reel, EFE the extended grade of the same body, HFE the 150 C version and MPFE the -55 C to 125 C version. The die and the pinout are common, so a change of grade does not touch the board. The power management cross reference maps those grades, BOM shortage recovery covers substitution during an allocation, and the one stop BOM page covers buying this line with the rest of the power parts on the same order.