Contact Us

LT3083MPQ#PBF

Brand: Analog Devices
Analog Devices LT3083MPQ#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3083MPQ#PBF — Analog & Mixed-Signal ICs | Superb Automation

LT3083MPQ#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3083MPQ#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3083MPQ#PBF: 3 A at minus 55 C in a 5-lead DD-Pak

The LT3083MPQ#PBF is the widest temperature grade of the 3 A single resistor linear regulator, in the 5-lead surface mount DD-Pak package, lead free finish, specified from -55 C to 125 C. Input range is 1.2 V to 23 V on this body and the output is adjustable from 0 V to 23 V with one resistor to the SET pin, using a 50 uA reference with 1 percent initial accuracy. Dropout is 310 mV, output noise is 40 uV RMS across 10 Hz to 100 kHz, load regulation is under 1 mV, line regulation is 0.001 percent per volt, the minimum load current is 1 mA and the part is stable with 10 uF of ceramic output capacitance.

Published values

ParameterValue
Input voltage1.2 V to 23 V
Output voltage0 V to 23 V, one resistor on SET
Output current3 A
Dropout voltage310 mV
Output noise40 uV RMS, 10 Hz to 100 kHz
SET pin current50 uA, 1 percent initial accuracy
Load regulationunder 1 mV
Minimum load current1 mA
Output capacitor10 uF ceramic minimum
Package5-lead DD-Pak, lead free
Temperature range-55 C to 125 C, MP grade

Why 3 A in a linear part still makes sense

A switching regulator is the efficient answer for a large step down, and it is the wrong answer when the noise or the transient matters more than the loss. Three amps from a 1.8 V input to a 1.2 V rail is a 0.6 V drop, so the dissipation is 1.8 W and the efficiency is 67 percent, which is acceptable in a rack product with air. The same current from 12 V to 1.2 V is 32 W of heat and belongs in a switcher with a linear post regulator. The buyer's question is therefore never the current alone but the voltage across the part, and a specification that quotes 3 A without the input and output is not enough to price or to build.

The DD-Pak tab is the output

On the 5-lead DD-Pak the tab is connected to the output, so the copper under the part is the regulated rail and not ground. That is convenient for heat, since the rail is usually a wide plane, and inconvenient for copper discipline, because the plane cannot be shared with a ground pour. The DD-Pak body exists for builds that need the thermal mass of a tabbed package while staying surface mount, and it is the version usually chosen when the board has no room for a TO-220. The same device is offered in a 16-lead TSSOP and a 12-lead 4 mm by 4 mm DFN with exposed pads, both of which need more careful copper work.

The 1 mA minimum load

This regulator needs at least 1 mA of load current to hold regulation. In a system where the 3 A rail also feeds a standby block that draws microamps, the rail can drift up when the main load turns off. The usual fix is a permanent bleeder resistor or a small always on load, and the value is set by the 1 mA figure at the lowest rail voltage. Buyers should check this against the sleep current budget of the product, because a 1 mA bleeder on a battery product is a real cost and a real constraint.

Grade and packing

The MPQ suffix is the MP grade in the DD-Pak, lead free, supplied in tubes rather than tape and reel. The I and E grades of the same body cover -40 C to 125 C and are the volume codes; MP is specified from -55 C for cold start applications. Moving between grades does not change the electrical table but does change screening and documentation, so a substitution from MP to I needs a cold start review. Our power management cross reference lists the grades and bodies, the ADI second source notes set out the checks for a substitute, and the lead time page shows schedules.