Contact Us

LT3082IDD#TRPBF

Brand: Analog Devices
Analog Devices LT3082IDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3082IDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3082IDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3082IDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3082IDD#TRPBF: 200 mA with a 3 mm DFN and reverse current protection

The LT3082IDD#TRPBF is the industrial grade of the 200 mA regulator in the 8-lead 3 mm by 3 mm DFN, on tape and reel and rated -40 C to 125 C. It carries the same core as the rest of the family: 1.2 V to 40 V input, 0 V to 38.5 V output from a 10 uA SET current, stability with 2.2 uF of ceramic output capacitance, 33 uV RMS of noise, 90 dB of rejection at 120 Hz, plus internal protection against reverse battery and reverse output current.

Published values

ParameterValue
Input voltage1.2 V to 40 V
Output voltage0 V to 38.5 V
Output current200 mA
SET pin current10 uA, 1 percent
Offset voltage0.5 mV typical between output and SET
Ripple rejection90 dB at 120 Hz, 20 dB at 1 MHz
Output noise33 uV RMS, 10 Hz to 100 kHz
Minimum output capacitor2.2 uF ceramic
Minimum load current0.5 mA
Thermal resistance25 C/W on 2500 square millimetres, 32 C/W at 225 square millimetres
Package and grade8-lead, 3 mm by 3 mm DFN, -40 C to 125 C, tape and reel

A resistor sets the rail, and one capacitor sets the noise

The 10 uA SET current flows through one resistor to ground, so the output is that current times the resistance: 100 kOhm gives 1 V, 330 kOhm gives 3.3 V, 1 MOhm gives 10 V. The offset between the output and the SET node is 0.5 mV typical, which is what makes the low output voltages practical. Adding a small capacitor from SET to ground bypasses the shot noise of that resistor and the noise of the reference current, and the output noise then falls to the error amplifier figure of 33 uV RMS. That capacitor is the single most effective noise decision on this part and costs nothing.

Reverse current, and why the DFN is not different

If the input collapses while the output capacitor is still charged, a conventional regulator will pull current backwards through its pass element and can latch or damage the upstream supply. The LT3082 blocks that path internally, and the same protection covers a reverse battery connection. The behaviour is the same in the DFN and the SOT-223 bodies because the protection is on the die. For a board with a large output capacitor and a connector that can be unplugged under load, this removes the external diode that would otherwise be needed, and removes its forward drop from the headroom budget.

The 3 mm body and its copper

With 25 C/W on 2500 square millimetres of copper and 32 C/W at 225 square millimetres, the DFN sits between the SOT-223 at 20 C/W and the SOT-23 at 54 C/W. At 200 mA with 1.7 V of differential the dissipation is 340 mW and the rise is about 9 C on a generous shape, which leaves the part cool in most cabinets. The pad is the output, so the copper under the body carries the rail and the heat at the same time, which is convenient until someone extends that copper into a ground pour. That is the one assembly mistake worth checking on the drawing.

Order code and stock

IDD is the industrial DFN on tape and reel, EDD the extended grade of the same body, IST the SOT-223 and ITS8 the 8-lead SOT-23. All of them share the die and the 10 uA SET current, so a body change keeps the passive parts. The power management cross reference maps the four bodies, BOM shortage recovery covers substitution between them, and the cost page shows the volume difference across the pack forms.