LT3080IST#TRPBF
Product Specifications
LT3080IST#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3080IST#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3080IST#TRPBF: 1.1 A adjustable regulator in the 3-lead SOT-223
The LT3080IST#TRPBF is the 3-lead SOT-223 version of the LT3080, a 1.1 A linear regulator whose output is set by one resistor and whose output can be adjusted all the way to zero. The three-lead body is the reason this code exists: the IN and VCONTROL pins are tied together inside the package, which removes the second supply rail that the five-lead versions need and makes the part a drop-in for older three terminal regulators. The trade is dropout, and it is a trade worth understanding before the footprint is committed.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 1.2 V to 36 V, IN and VCONTROL tied internally |
| Output voltage | 0 V to 36 V, set by one resistor on SET |
| Output current | 1.1 A, current limit 1.1 A minimum |
| SET pin current | 10 uA, 1 percent initial accuracy |
| VIN dropout | 100 mV at 100 mA, 350 mV at 1.1 A typical |
| Output offset | plus or minus 5 mV, SOT-223 and DD-Pak grade |
| Minimum load | 300 uA typical, 1 mA maximum |
| Output noise | 40 uV RMS, 10 Hz to 100 kHz |
| Ripple rejection | 75 dB at 120 Hz, 55 dB at 10 kHz, 20 dB at 1 MHz |
| Thermal resistance | 55 C/W junction to ambient, 15 C/W to case |
| Package | 3-lead SOT-223, tab is OUT, tape and reel |
The dropout figure this package actually delivers
The headline 350 mV is a VIN dropout figure and it belongs to the parts that have a separate VCONTROL pin. In the SOT-223 the two supplies are one, so the regulator needs the VCONTROL headroom instead: 1.2 V at 100 mA and 1.35 V at 1.1 A, with 1.6 V as the maximum over temperature. On a 5 V to 3.3 V rail that is invisible, because 1.7 V of headroom covers either number. On a 3.3 V to 2.5 V rail it is decisive: 800 mV will not hold 1.1 A in this package, whatever the front page says. The honest reading is that the three-lead part is a 5 V class regulator, and the five-lead bodies are the ones for low headroom rails.
The tab is the output, and it is live
On this package the tab is connected to OUT, not to ground. That has three consequences. The heat path is the output node, so the copper under the tab is at the regulated voltage and must not be shared with a ground pour. A heat sink bolted to the tab is at the output potential, which rules out a shared sink across several rails. And the tab's 15 C/W junction to case is a real number only if the tab is soldered to a copper area, so the 55 C/W junction to ambient figure is what applies to a part sitting on a minimal footprint. At 1.87 W, a 5 V to 3.3 V drop at 1.1 A, a 55 C/W path gives about 103 C of rise, which is why this body is normally used at half an amp or with a serious copper pad.
One resistor, and the minimum load
The output is the SET resistor times 10 uA, so 100 kOhm gives 1 V, 330 kOhm gives 3.3 V and 500 kOhm gives 5 V, and the initial accuracy of that current is 1 percent with a 9.8 to 10.2 uA window over temperature. Because the reference is a current rather than a voltage, there is no divider ratio to trim and the same resistor gives the same rail on every board. The part needs a minimum load of 300 uA typical and 1 mA maximum to stay in regulation, which is the quiescent current flowing to the output; a rail that is switched off into a high impedance load is where this requirement bites. Adding a capacitor across the SET resistor, up to 1 uF, lowers the output noise but slows the start up in proportion to the resistor and capacitor product.
Sourcing the three-lead body
The SOT-223 code is popular because it replaces older three terminal regulators without a board change, so it is the first of the LT3080 bodies to go short when a program ramps. Files that carry several LT3080 bodies are best held on one cross reference, which is what the power management cross reference covers. Substitution between the E and I grades on the same body is a documentation change, while substitution to a five-lead body is a board change, and the difference is set out on the component cost page. Short lines are worked on the BOM shortage recovery page.