Contact Us

LT3080IQ#TRPBF

Brand: Analog Devices
Analog Devices LT3080IQ#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3080IQ#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3080IQ#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3080IQ#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3080IQ#TRPBF: 1.1 A in the 5-lead DD-Pak with a 30 C/W heat path

The LT3080IQ#TRPBF is the I grade of the LT3080 in the 5-lead DD-Pak, taped and reeled. It is the body to choose when the regulator has to lose real power: 30 C/W junction to ambient and 3 C/W junction to case, against 55 and 15 for the three-lead SOT-223. The electrical behaviour is the family behaviour, with the important difference that this package brings VCONTROL out as a separate pin, so the 350 mV dropout figure applies and the part can hold 1.1 A from a low headroom rail.

Published values

ParameterValue
Input voltage1.2 V to 36 V on VIN, VCONTROL up to 36 V
Output voltage0 V to 36 V, set by one resistor
Output current1.1 A, current limit 1.1 A minimum, 1.4 A typical
VIN dropout100 mV at 100 mA, 350 mV at 1.1 A typical, 500 mV maximum
VCONTROL dropout1.2 V at 100 mA, 1.35 V at 1.1 A, 1.6 V maximum
VCONTROL pin current4 mA at 100 mA, 17 mA at 1.1 A, about 1.7 percent of load
SET pin current10 uA, 1 percent initial
Output offsetplus or minus 5 mV on this package
Output noise40 uV RMS, 10 Hz to 100 kHz
Thermal resistance30 C/W junction to ambient, 3 C/W to case
Package5-lead DD-Pak, tab is OUT

Two supplies, two requirements

The pin that separates this body from the SOT-223 is VCONTROL. It feeds the control circuitry and the pass transistor's base, it draws about 1.7 percent of the output current, and it must sit 1.2 V to 1.35 V above the output for the part to regulate. A separate VCONTROL rail is not optional overhead: it is what lets the IN pin sit only 100 mV above the output at light load and 350 mV at full current, which is the whole point of the architecture. On a board with a 1.8 V rail available, tying VCONTROL to 5 V and feeding IN from a 3.3 V bus gives a 1.5 V output at 1.1 A with 1.5 V across the pass element rather than 1.8 V, and that difference is 330 mW of heat in a package whose thermal path can be sized for it.

Dissipation arithmetic that decides the body

At 1.87 W, a 5 V to 3.3 V drop at 1.1 A, the DD-Pak with a 30 C/W path rises about 56 C, which puts the junction at 116 C in a 60 C box; the SOT-223 at 55 C/W would be at 163 C and outside its window. That is the entire case for this package. Two things follow. First, the thermal number assumes the tab is soldered to a copper area sized for it, and the tab is at the output potential, so the pour cannot be shared with ground. Second, once the current is split across two devices the rise halves and the SOT-223 becomes viable again: the outputs can be tied together through small ballast resistors, and the vendor shows better than 80 percent sharing with 10 mOhm of PC trace per device, which is a few millimetres of one ounce copper.

Where the current limit steps aside

The part carries 1.1 A minimum of current limit, and the vendor notes that current limit may fall to zero when the input to output differential exceeds 25 V on the DFN and MSOP bodies or 26 V on this one. Both pins are rated to 36 V absolute, so a 36 V input with a 5 V output is allowed by the pin ratings and not by the current limit. In practice a 24 V to 3.3 V rail is a 20.7 V differential and stays inside the note, while a 28 V to 3.3 V rail at 24.7 V is on the edge for the small bodies and still inside for this one. Files that run a wide differential should check that line before anything else, because a regulator that loses its current limit protection at high differential is a fault behaviour problem, not a thermal one.

Grade and availability

The I grade is guaranteed over minus 40 C to 125 C, and the E grade on the same body is tested at 25 C with the same window assured by characterization. Both are orderable on tape and reel. Keeping the LT3080 bodies on one cross reference is the cheapest way to see which package is in stock when a line goes short, which is what the power management cross reference is for. Sourcing routes for a short line are on the BOM shortage recovery page, and the trade between one 1.1 A device and two smaller ones sits on the component cost page.