Contact Us

LT3080IDD#TRPBF

Brand: Analog Devices
Analog Devices LT3080IDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3080IDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3080IDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3080IDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3080IDD#TRPBF: 1.1 A adjustable regulator in the 3 mm DFN

The LT3080IDD#TRPBF is the I grade of the LT3080 in the 8-lead 3 mm by 3 mm DFN, taped and reeled. It is the smallest body in the family and the one with the widest junction to ambient figure, 64 C/W against 30 C/W for the DD-Pak. The electrical behaviour is unchanged across bodies: 1.2 V to 36 V input, output adjustable from zero to 36 V by one resistor, 1.1 A, 40 uV RMS of noise, plus or minus 2 mV of output offset, and current limit with foldback. What the DFN buys is 3 mm of board area; what it costs is thermal margin.

Published values

ParameterValue
Input voltage1.2 V to 36 V, VCONTROL separate
Output voltage0 V to 36 V, set by one resistor
Output current1.1 A, 1.4 A typical current limit
SET pin current10 uA, 1 percent initial accuracy
VIN dropout100 mV at 100 mA, 350 mV at 1.1 A typical
VCONTROL dropout1.2 V at 100 mA, 1.35 V at 1.1 A
Output offsetplus or minus 2 mV
Minimum load300 uA typical, 1 mA maximum
Thermal regulation0.003 percent per watt, 10 ms pulse
Thermal resistance64 C/W junction to ambient, 3 C/W to case
Package8-lead 3 mm DFN, exposed pad is OUT, pin 9

The 64 C/W figure and what it rules out

The junction to case number is the best in the family at 3 C/W, and the junction to ambient number is the worst at 64 C/W. That pair tells the whole story: the die can shed heat into a board very efficiently, and it has almost no path without one. On a two layer board with 100 square millimetres of copper on the output island the effective number lands near the published figure; on a four layer board with the island stitched into inner copper it improves, but never to the DD-Pak's 30 C/W, because the package has no tab. At 1.5 W the rise is 96 C, which leaves a 30 C ambient as the practical ceiling. Any file that expects a full amp at 5 V in and 3.3 V out from this body in a warm enclosure is looking at the wrong package.

Where a 3 mm body still wins

The DFN is right when the load is modest, the board is tight, and the regulator is close to the point of load. Post regulation of a switching rail is the typical case: a 3.6 V intermediate bus feeding 2.5 V at 400 mA is 440 mW, which is 28 C of rise and comfortable. The same body is also the right answer when several rails are needed in a small area, since two 3 mm parts occupy less space than one DD-Pak and split the heat between two islands. The vendor's own guidance points the same way: the part can be paralleled, outputs tied through small ballast resistors with the SET pins and IN pins common, and better than 80 percent sharing is reported with 10 mOhm of trace per device.

What has to be true on the board

Four board conditions decide whether this package behaves. The exposed pad is the output node, so it needs a solid island that is not part of the ground pour and is stitched with vias to a matching island on the other side. The output capacitor is 2.2 uF of ceramic minimum, and its effective value at the operating voltage is what counts, since a Y5V part can lose most of its capacitance at 5 V. The SET capacitor, up to 1 uF, lowers noise but lengthens start up in proportion to the resistor and capacitor product. And the minimum load of 300 uA typical, 1 mA maximum, has to be present for the output to regulate, which is normally satisfied by the feedback resistor itself when the divider is sized for 10 uA per volt of output.

Fault behaviour at high differential

The current limit is 1.1 A minimum and 1.4 A typical, and the vendor notes that the limit may fall to zero when the input to output differential exceeds 25 V on this body, against 26 V on the SOT-223, DD-Pak and TO-220 versions. Both pins are rated to 36 V absolute, so a 36 V to 3.3 V rail is within the pin ratings and outside the current limit guarantee. A 24 V to 3.3 V rail is a 20.7 V differential and stays inside. The other protection is thermal, and with 64 C/W the thermal limit is reached quickly, so a high differential fault on this body ends in thermal cycling rather than in a steady fault current.

Grade and supply

The I grade is guaranteed from minus 40 C to 125 C, and the E grade on the same footprint is tested at 25 C. The footprint is shared, so a grade change is a documentation change rather than a board change, which is the cheapest kind of substitution in a shortage. Keeping the LT3080 bodies on one cross reference is what the power management cross reference is for. Short lines are worked on the BOM shortage recovery page, and the comparison of one wide body against two narrow ones is on the component cost page.