Contact Us

LT3080EST#TRPBF

Brand: Analog Devices
Analog Devices LT3080EST#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3080EST#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3080EST#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3080EST#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3080EST#TRPBF: the standard grade three-lead version for retrofit rails

The LT3080EST#TRPBF is the E grade of the LT3080 in the 3-lead SOT-223, taped and reeled. It is the code that most often replaces an older fixed three terminal regulator on an existing board, because the pinout is familiar, the tab is the output, and the output voltage is set by one resistor instead of being fixed by the part number. The E suffix means tested at 25 C with the 125 C window assured by characterization; the three-lead body means the IN and VCONTROL pins are tied together internally, which is what makes the simple footprint possible and what limits the dropout.

Published values

ParameterValue
Input voltage1.2 V to 36 V, IN and VCONTROL tied internally
Output voltage0 V to 36 V, one resistor on SET
Output current1.1 A, 1.1 A minimum current limit
SET pin current10 uA, 1 percent initial
VCONTROL dropout1.2 V at 100 mA, 1.35 V at 1.1 A, 1.6 V maximum
Output offsetplus or minus 5 mV on this package
Minimum load300 uA typical, 1 mA maximum
Output noise40 uV RMS, 10 Hz to 100 kHz
Ripple rejection75 dB at 120 Hz, 20 dB at 1 MHz
Thermal resistance55 C/W junction to ambient, 15 C/W to case
Package3-lead SOT-223, tab is OUT

The retrofit arithmetic

A three terminal regulator in this footprint is normally fed from a rail with 1.5 V to 2 V of headroom, so the headroom question rarely comes up in the retrofit case. Where it does come up is a 3.3 V bus feeding a 2.5 V rail: the 800 mV of headroom is inside the 350 mV VIN dropout figure and outside the 1.35 V VCONTROL figure that this package actually needs. The second thing to check is the output capacitor: an older part may have been specified with a tantalum of several microfarads and an ESR that the new part does not need, and the LT3080 is stable with 2.2 uF of ceramic, so a smaller and cheaper capacitor is normally correct. The third is the minimum load of 300 uA typical and 1 mA maximum, which is more than some legacy circuits draw when their load is switched off.

Grade, documentation and cold start

The E and I codes on this body have the same electrical table and the same footprint. The E grade is tested at 25 C and its performance from 0 C to 125 C is guaranteed, with the cold end assured by characterization; the I grade covers minus 40 C to 125 C by test. For an indoor retrofit that is a distinction without a difference. For a board that ships to a site where the first power up happens in winter, it is the difference between a specification and a hope, and the cost of the I grade is small enough that the paperwork is usually the deciding factor. A buyer reading a distributor page that lists both codes under one description should check the suffix, because the price delta does not always follow the grade.

Heat in a three-lead body

The tab is the output and it is the only heat path, at 15 C/W junction to case, with 55 C/W junction to ambient on a minimal footprint. At 1.87 W, a 5 V to 3.3 V drop at 1.1 A, the rise is about 103 C, which puts a 60 C ambient at 163 C and outside the window. The practical operating point for this body is half an amp, or a full amp with a real copper pad on the tab and some airflow. Two parts in parallel halve the dissipation per device and bring the rise to about 51 C, which is why the three-lead code shows up on rails that need an amp in a small space. The sharing depends on the 5 mV offset between SET and OUT on this package, and 10 mOhm of trace per output is the usual ballast.

Noise and the SET capacitor

The bare part is 40 uV RMS from 10 Hz to 100 kHz, with 75 dB of rejection at 120 Hz falling to 20 dB at 1 MHz, which is the number to remember when the input comes from a switching converter running at a few hundred kilohertz. A capacitor from SET to ground, up to 1 uF, bypasses the SET resistor noise and lowers the output noise further, and it also sets the start up ramp. Ripple rejection above 100 kHz is modest, so a ferrite bead or an LC filter ahead of the part does more for a switching input than a larger output capacitor does.

Buying the three-lead code

This body is the volume code in the family, so it is stocked widely and also the first to disappear when a large program ramps. Keeping it on a cross reference with the other LT3080 bodies shows immediately whether the five-lead parts are available as an alternative, which is what the power management cross reference does. Short lines are worked on the BOM shortage recovery page, and the cost of moving a rail to a different body is set out on the component cost page.