Contact Us

LT3080EQ#TRPBF

Brand: Analog Devices
Analog Devices LT3080EQ#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3080EQ#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3080EQ#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3080EQ#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3080EQ#TRPBF: standard grade 1.1 A regulator in the 5-lead DD-Pak

The LT3080EQ#TRPBF is the E grade of the LT3080 in the 5-lead DD-Pak, taped and reeled. It is the highest power body in the family at 30 C/W junction to ambient and 3 C/W junction to case, and it keeps the separate VCONTROL pin, so the 350 mV dropout applies and the part holds 1.1 A from a rail only a few hundred millivolts above the output. The E suffix is the qualification: tested at 25 C, 0 C to 125 C guaranteed, cold end assured by characterization.

Published values

ParameterValue
Input voltage1.2 V to 36 V on VIN, VCONTROL up to 36 V
Output voltage0 V to 36 V, one resistor on SET
Output current1.1 A, 1.4 A typical current limit
VIN dropout100 mV at 100 mA, 350 mV at 1.1 A, 500 mV maximum
VCONTROL dropout1.2 V at 100 mA, 1.35 V at 1.1 A, 1.6 V maximum
VCONTROL pin currentabout 1.7 percent of output current, 17 mA at 1.1 A
SET pin current10 uA, 1 percent initial
Output offsetplus or minus 5 mV on this package
Output noise40 uV RMS, 10 Hz to 100 kHz
Thermal resistance30 C/W junction to ambient, 3 C/W to case
Package5-lead DD-Pak, tab is OUT

Why the control rail pays for itself

A separate VCONTROL pin sounds like an extra rail to route, and on a board that already has 5 V it is free. The return is dropout: with VCONTROL at 5 V and IN at 3.3 V, a 2.5 V output at 1.1 A runs with 800 mV across the pass element, which is 0.88 W, against 1.87 W if the input had to be 5 V. That is 55 C of junction rise avoided on a 30 C/W body, and it is the difference between a 60 C box being comfortable and being marginal. The cost is the 17 mA that VCONTROL draws at full load, about 1.7 percent of the output current, which the upstream 5 V rail has to supply. On a 3.3 V only board the same trick works with IN fed from a switching pre regulator and VCONTROL from the 3.3 V rail.

Mechanical and thermal notes

The DD-Pak is a surface mount body with a tab that is also the output, so the copper under it is at the regulated voltage and cannot join the ground pour. The 3 C/W junction to case figure assumes the tab is reflowed to a copper area sized for the dissipation; without that area the 30 C/W ambient figure is optimistic. At 1.87 W the rise on the ambient figure is 56 C, so a 60 C box lands near 116 C, inside the 125 C limit but with nothing left. Adding a matching copper area on the other side of the board with vias through, or dropping the differential, are the two levers that actually move that number. Bolting on a shared heat sink is not an option, because every sink bolted to a tab sits at that rail's output voltage.

Minimum load and the one resistor

The output is the SET resistor times 10 uA: 100 kOhm for 1 V, 250 kOhm for 2.5 V, 500 kOhm for 5 V, with 1 percent initial accuracy and a 9.8 to 10.2 uA window over temperature. Because there is no divider ratio, the tolerance of the rail is the current tolerance plus the resistor tolerance, and the same resistor gives the same rail across a product family. The part needs 300 uA typical and 1 mA maximum of load to stay in regulation, which is the quiescent current flowing to the output; a rail that is disabled by a downstream switch and left with no load can drift up. A 1 kOhm permanent bleed resistor solves it at 3.3 mA, which is more than the part itself consumes, so the usual answer is a load that is never fully removed.

Fault and grade decisions

Current limit is 1.1 A minimum and folds back, and the vendor notes that the limit may fall to zero above a 26 V input to output differential on this body, so a 36 V bus feeding 3.3 V is outside the protected region even though the pin ratings allow it. The E grade covers 0 C to 125 C by guarantee, with the cold end by characterization; where a file needs minus 40 C by test, the I grade on the same footprint is the substitution and the board does not change. Files that carry both are best kept on one cross reference, which is what the power management cross reference shows. Short lines are worked on the BOM shortage recovery page, and the cost arithmetic for a body change is on the component cost page.