LTC6090CS8E-5#TRPBF
Product Specifications
LTC6090CS8E-5#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC6090CS8E-5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC6090CS8E-5#TRPBF: 140 V of Supply, and a Minimum Gain of Five
The LTC6090CS8E-5#TRPBF is a high voltage CMOS operational amplifier that runs from plus and minus 4.75 V to plus and minus 70 V, a 140 V total supply. Noise is 3.5 uV peak to peak from 0.1 Hz to 10 Hz and 11 nV per root hertz, input bias current is 50 pA maximum, offset is 1.25 mV maximum with plus or minus 5 uV per degree C of drift, common mode rejection is 130 dB minimum, the output is rail to rail and sinks or sources 50 mA, gain bandwidth is 12 MHz, slew rate is 21 V per microsecond, and the output drives 200 pF. A thermal warning flag goes active as the die approaches 150 C and can be wired to the output disable pin to protect the stage. The -5 suffix in this order code is the decompensated version, stable only in noise gain configurations of five or greater; the plain LTC6090 is unity gain stable. Both come in a thermally enhanced SOIC-8 or TSSOP-16 with an exposed pad, and the vendor lists the part as recommended for new designs.
This is the amplifier for a piezo actuator, an ATE pin driver, a photodiode bias servo or a high voltage regulator, where the signal has to swing over tens of volts and the source impedance is high. Fifty picoamps of bias current is what makes a 10 Mohm photodiode or a high value divider usable without a guard ring.
The -5 suffix is a stability requirement, not a grade
This order code is the decompensated part. It is stable at a noise gain of five or more, so a follower or a gain of two built with it will oscillate, and the 12 MHz gain bandwidth at the minimum gain of five is 2.4 MHz. The plain LTC6090 is unity gain stable and is the part to order for a buffer. Both carry the same voltage rating and the same package, so the suffix decides whether the circuit works at all, and a purchase order that omits it can deliver an amplifier that is unusable in a buffer and perfectly fine in a gain of ten.
The slew rate sets the large signal bandwidth. At 140 V peak to peak, 21 V per microsecond is 47.7 kHz; at 20 V peak to peak it is 334 kHz. The 12 MHz gain bandwidth is a small signal figure and has nothing to do with either, which is why a high voltage stage that is specified from the gain bandwidth alone comes out an order of magnitude faster on paper than on the bench.
Fifty milliamps at 140 V would be 7 W, and the package cannot pass it
The output stage is rated 50 mA and the supply is rated 140 V, and those two numbers do not multiply into a continuous operating point. Seven watts through an SOIC-8 with an exposed pad, on a path of roughly 40 degrees per watt, is a 280 degree rise; the die would reach its thermal warning flag and then its disable long before steady state. So the 50 mA is a transient and fault rating, and the continuous current at high voltage is set by the thermal path and by the load duty cycle, not by the output stage.
The thermal warning flag wired to the output disable pin is the mechanism the vendor provides for exactly this. Rather than calculating the worst case and hoping, the stage turns itself off when the die reaches the limit and the system sees a fault rather than a destroyed part. A piezo driver that fires in bursts is the natural application: high current for microseconds, thermal recovery in between.
| Supply | Plus and minus 4.75 V to plus and minus 70 V, 140 V total |
| Stability | Noise gain of five or greater on this -5 suffix, unity gain stable on the plain part |
| Bandwidth | 12 MHz gain bandwidth, 2.4 MHz at the minimum gain of five |
| Slew limit | 21 V per microsecond, 47.7 kHz at 140 V peak to peak, 334 kHz at 20 V |
| Offset and drift | 1.25 mV maximum, 8.9 ppm of a 140 V span, 5 uV per degree C, 825 uV over 165 degrees |
| Bias current | 50 pA maximum, 0.5 mV into 10 Mohm, 1.25 mV into 25 Mohm |
| Noise | 3.5 uV peak to peak from 0.1 to 10 Hz, 11 nV per root hertz, 11 uV over 1 MHz |
| Output | Rail to rail, 50 mA sink and source, 200 pF load, 7 W at 140 V |
| Protection | Thermal warning flag at 150 C, output disable pin, thermally enhanced package |
| Package | SOIC-8E and TSSOP-16E with exposed pad |
Two questions buyers ask
Can it drive a piezo actuator continuously?
The current rating allows it and the thermal path does not. A piezo that draws 50 mA at 100 V dissipates 5 W in the amplifier, which the package cannot hold without a heatsink and airflow. Pulsed operation with a defined duty cycle, or a discrete output stage inside the loop, is how a continuous high power piezo load is normally handled.
Does 50 pA of bias current matter at 10 Mohm?
It is 0.5 mV, which is 40 percent of the 1.25 mV offset, and at 25 Mohm it equals the offset. Below about 1 Mohm the offset dominates and the bias current is irrelevant; above 10 Mohm the bias current is the larger error term and the resistor values have to come down or the node has to be guarded.
Ordering and supply
The CS8E suffix is the commercial grade in the thermally enhanced SOIC-8, and the -5 before it is the decompensated stability grade. The exposed pad is part of the thermal rating and not an optional copper pour, so a board that leaves it unconnected has a lower current capability than the data sheet describes.
We source this family for production and for repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the amplifier cross reference, and where a high voltage amplifier has to replace one that is out of stock, pin to pin cross reference shows whether the compensation, the exposed pad and the disable pin land on the same pads before the loop is rechecked.
Request Quote — In Stock, 100% New & Original, Full Warranty