LTC5510IUF#TRPBF
Product Specifications
LTC5510IUF#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC5510IUF#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC5510IUF#TRPBF: A 6 GHz Mixer That Takes 0 dBm of LO and 11 dBm at the Input
The LTC5510IUF#TRPBF is a double-balanced active mixer with an input buffer and a high speed LO amplifier, specified from 1 MHz to 6 GHz on the input and LO ports, with a 50 ohm matched input from 30 MHz to beyond 3 GHz. Conversion gain is 1.5 dB, output third order intercept is 27 dBm at an output of 1575 MHz, noise figure is 11.6 dB at the same output, and input 1 dB compression is 11 dBm on a 5 V supply. The LO needs only 0 dBm, the LO input impedance stays matched whether the part is enabled or shut down, and the die carries a temperature monitor. Supply current is 105 mA from 5 V or 3.3 V, the package is a 16-lead 4 mm by 4 mm QFN, and the part is in production at the vendor.
Two numbers on that list decide whether this mixer fits a receiver: 11 dBm of input compression and 27 dBm of intercept, with a conversion gain of only 1.5 dB. That combination describes a mixer that is linear at the input rather than one that hides a loss behind the gain of the stage after it.
Output compression is 12.5 dBm, so the intercept sits 14.5 dB above it
Input compression of 11 dBm plus 1.5 dB of conversion gain is 12.5 dBm at the output. The intercept is 27 dBm, so the two are 14.5 dB apart. A receiver that needs 60 dB of spurious free dynamic range from this stage has to keep the output below 12.5 dBm, and the two tone level that produces third order products at the noise floor follows from the intercept rather than from the compression point. In a wideband front end where several carriers arrive together, the intercept is the number that sets the blocker budget, and the compression point is the number that sets the largest single carrier.
Noise figure of 11.6 dB means the mixer contributes a noise floor of about -162.4 dBm in 1 Hz, which is the figure to carry into a cascade calculation. In a receiver with no preceding low noise amplifier the mixer dominates the sensitivity, and in a receiver with one, the gain ahead of the mixer sets how much of that 11.6 dB survives.
1 MHz to 6 GHz is 12.55 octaves on one die
The input and LO ports cover 1 MHz to 6 GHz, which is 12.55 octaves, and the vendor specifies the input as 50 ohm matched from 30 MHz to beyond 3 GHz. The part is built for 1:1 transmission line baluns, so the wideband match comes from the balun rather than from a narrowband network on the board, and the same board can serve an HF receiver and a 5.8 GHz link with a different balun. Up-conversion and down-conversion both work from the same port pair.
The LO port is the part that surprises people. It needs 0 dBm, it can be driven single ended or differentially, and its impedance does not change when the mixer is shut down, so a synthesizer driving several mixers sees the same load on the enabled and disabled ones. Low LO leakage to the output is quoted as a reason the output filter can be smaller, which matters when the intermediate frequency is close to the LO.
5 V is the specified supply and 3.3 V is the reduced one
At 5 V and 105 mA the part dissipates 525 mW, and at 3.3 V and the same current it dissipates 346.5 mW. The vendor states that 3.3 V operation gives slightly reduced performance rather than the same numbers, so a board that quotes 27 dBm of intercept on a 3.3 V rail is quoting a 5 V figure. The shutdown control removes the supply current when the receive path is idle, and the on-chip temperature monitor is there for a system that has to derate the front end as the board heats.
| Function | Double-balanced active mixer, up-conversion and down-conversion |
| Input and LO range | 1 MHz to 6 GHz, 50 ohm matched input from 30 MHz to beyond 3 GHz |
| Conversion gain | 1.5 dB at an output of 1575 MHz |
| Output intercept | 27 dBm at an output of 1575 MHz |
| Input compression | 11 dBm at 5 V, which is 12.5 dBm at the output |
| Noise figure | 11.6 dB, a -162.4 dBm per Hz input floor |
| LO drive | 0 dBm, single ended or differential, impedance held in shutdown |
| Supply | 5 V at 105 mA, 525 mW, or 3.3 V at 105 mA, 346.5 mW |
| Extras | Shutdown control, on-chip temperature monitor |
| Package and range | 16-lead 4 mm by 4 mm QFN, minus 40 to 105 C case |
Two questions buyers ask
Is this a drop-in for a passive mixer on an existing board?
No. A passive mixer has no supply pin, no LO buffer and usually a different pin count, and this part draws 105 mA and needs the LO at 0 dBm into a matched port. The pin map has to be compared pin by pin, and the conversion gain of 1.5 dB changes the gain plan of every stage after it, so a socket swap also changes the baseband amplifier settings.
Does the LO match stay valid with the supply removed?
The LO input impedance is quoted as always matched, and the shutdown control is a logic input rather than a supply removal. A board that removes the 5 V rail to save power does not get the same behaviour as one that asserts shutdown, and the LO drive level of 0 dBm has to be present for the port to present its specified impedance.
Ordering and supply
The IUF suffix is the 16-lead QFN body on the industrial grade, and TRPBF is tape and reel, lead free. The 4 mm by 4 mm body is the whole family, so the order code here is about grade and packing rather than about a pin count change. The vendor ships this part from stock, and the second source question is usually about a pin compatible mixer from another vendor rather than about a different LTC option.
We hold this family for production builds and for repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the pin to pin cross reference, and where a mixer has to go into a board that is already built, the checks in how to verify a drop in replacement put the LO drive level and the gain plan ahead of the socket fit.
Request Quote — In Stock, 100% New & Original, Full Warranty