Contact Us

LT3080EDD#TRPBF

Brand: Analog Devices
Analog Devices LT3080EDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3080EDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3080EDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3080EDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3080EDD#TRPBF: standard grade 1.1 A regulator in the 3 mm DFN

The LT3080EDD#TRPBF is the E grade of the LT3080 in the 8-lead 3 mm by 3 mm DFN, taped and reeled. It is the smallest body in the family at 64 C/W junction to ambient and 3 C/W junction to case, and it shares the plus or minus 2 mV output offset of the DFN and MSOP versions. The electrical table is the family table: 1.2 V to 36 V input, output adjustable from zero to 36 V by one resistor, 1.1 A, 40 uV RMS of noise, and current limit with foldback. The E suffix means tested at 25 C with the 125 C window assured by characterization.

Published values

ParameterValue
Input voltage1.2 V to 36 V, VCONTROL separate
Output voltage0 V to 36 V, one resistor on SET
Output current1.1 A, 1.1 A minimum current limit
SET pin current10 uA, 1 percent initial
VIN dropout100 mV at 100 mA, 350 mV at 1.1 A
Output offsetplus or minus 2 mV
Minimum load300 uA typical, 1 mA maximum
Output noise40 uV RMS, 10 Hz to 100 kHz
Thermal regulation0.003 percent per watt at a 10 ms pulse
Thermal resistance64 C/W junction to ambient, 3 C/W to case
Package8-lead 3 mm DFN, exposed pad is OUT, pin 9

Thermal regulation as a quality signal

The datasheet quotes 0.003 percent per watt of thermal regulation, measured with a 10 ms pulse so the number reflects the die and not the board. That is 30 uV on a 1 V output for every watt dissipated, or about 0.1 mV on a 3.3 V rail at 1 W. It matters on a rail that has to stay accurate while the load moves, because it is a real output shift that follows power rather than a measurement artefact. It also explains a symptom that catches test engineers: a rail that reads 20 uV high on a bench at 100 mA and 60 uV high at 1 A is not oscillating, it is the die warming up.

Where this body belongs

At 64 C/W this is a low to medium dissipation part whatever the current rating says, and the right role is post regulation of a switching rail at a few hundred milliamps, or a full amp where there is a real copper island and some air. A 3.6 V to 2.5 V drop at 800 mA is 880 mW and 56 C of rise, which is the edge of comfort in a 50 C box. The same rail at 1.1 A from 5 V is 1.87 W and 120 C of rise, which is not a working point at all. The vendor's own framing is that the part spreads heat across surface mount boards when it is paralleled, and that is the honest use for the small bodies: two devices, two islands, half the rise each.

Board rules that cannot be skipped

The pad is the output, so its copper island is live and separate from ground. It must be stitched with vias to a matching island on the other side, and those vias cannot land in the ground plane. The output capacitor is 2.2 uF of ceramic minimum, chosen for stability, and its effective capacitance at the operating voltage is the number that matters, since a Y5V part at 5 V can read a fraction of its marked value. The SET capacitor, up to 1 uF, trades noise for start up time. And the 1 mA maximum minimum load is a real requirement: a rail with a switchable load that goes open will drift up out of regulation, which shows up as a phantom fault on the downstream circuit.

Ordering and substitution

The EDD code shares its footprint with the IDD code, so moving between the two is a documentation change and not a board change. Moving to the MSOP or the DD-Pak is a footprint change, and moving to the three-lead SOT-223 also changes the dropout behaviour because the control pin disappears. In a shortage all three cases come up at once, which is why keeping the family on one cross reference pays, as the power management cross reference shows. Short lines are worked on the BOM shortage recovery page, and the cost arithmetic for body and grade changes is on the component cost page.