LT1964IS5-BYP#TRPBF
Product Specifications
LT1964IS5-BYP#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT1964IS5-BYP#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT1964IS5-BYP#TRPBF: A Negative Regulator's Dropout Is Measured From the Rail It Sits On
The LT1964 is a 200 mA negative low dropout regulator with 340 mV of dropout, 30 uA of quiescent current, 3 uA in shutdown and 30 uV rms of output noise once the 0.01 uF bypass capacitor is fitted, in a 5-lead ThinSOT or an 8-lead DFN. It is the negative complement to the LT1761 family, which is why it appears on analogue boards that already have positive rails from that family. The IS5 code is the 5-lead ThinSOT body, and the BYP suffix is the version that brings the bypass pin out, which is the difference between the 30 uV noise figure and whatever the part does without it.
Negative rails dissipate more than they look
A negative regulator referenced to ground passes the same current at a larger differential than a positive one at the same magnitude: minus 12 V to minus 5 V at 200 mA is 1.4 W, while 12 V to 5 V is the same 1.4 W, but the 5 V output at 200 mA is only 1 W of useful power, so the efficiency is 42 percent. In a 1 mm tall ThinSOT that 1.4 W is not available, and the practical load at a 12 V input is nearer 50 mA, which is 0.35 W. A minus 5 V rail derived from the same 5 V that feeds the positive side is not possible, which is why the negative rail usually comes from a charge pump or a transformer winding and carries the dropout of both stages.
| Input to output | Dissipation at 200 mA | Dissipation at 50 mA |
|---|---|---|
| Minus 12 V to minus 5 V | 1.40 W | 0.35 W |
| Minus 8 V to minus 5 V | 0.60 W | 0.15 W |
| Minus 5.4 V to minus 5 V | 0.08 W | 0.02 W |
| Minus 15 V to minus 12 V | 0.60 W | 0.15 W |
Dropout, reference and the adjustable version
The 340 mV of dropout at 200 mA means a minus 5 V output needs about minus 5.34 V at the input, which is why a minus 5.4 V pre-regulator is the usual pairing. The fixed version is minus 5 V and the adjustable version uses a 1.22 V reference and reaches minus 20 V, so a minus 15 V rail is an adjustable part and not a fixed one. The reference is referred to ground rather than to the negative rail, which is what makes the part easy to use with a positive control signal: the shutdown pin accepts either polarity, so a 3.3 V logic line can turn the rail off without a level shifter.
Noise, bypass and stability
The 30 uV rms figure over 10 Hz to 100 kHz is measured with a 0.01 uF capacitor on the bypass pin, and that capacitor also lengthens the start up, so a rail that must come up in a defined order needs the ramp accounted for. The regulator is stable with a 1 uF output capacitor and works with ceramic, tantalum or aluminium, which removes the ESR selection exercise that older negative regulators required. Reverse output protection and thermal limiting are internal, and both matter on a negative rail because a short to ground pulls the output above the input and the usual diode is easy to forget.
The negative rail in a mixed signal board
Pairs of positive and negative rails at the same current are not interchangeable parts, and a shortage on the negative device cannot be covered by the positive one with the pins reversed. The power management cross reference page covers the pairing, the amplifier cross reference page covers the amplifiers that need the negative rail, and incoming checks follow the incoming inspection plan.