Contact Us

LT3060ITS8#TRPBF

Brand: Analog Devices
Analog Devices LT3060ITS8#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3060ITS8#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3060ITS8#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3060ITS8#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3060ITS8#TRPBF: adjustable 100 mA regulator, industrial grade, ThinSOT

The LT3060ITS8#TRPBF is the adjustable LT3060 in the 8-lead ThinSOT, tape and reel, I grade. A 600 mV internal reference and an external divider set the output anywhere from 600 mV to 44.5 V, the input works from 1.6 V to 45 V, and the part delivers 100 mA with 40 uA of quiescent current. Industrial temperature coverage runs minus 40 C to 125 C at the junction and is guaranteed over that window rather than inferred from a 25 C test. It is the code for a rail that is not one of the seven fixed voltages, or for a product family that wants one part number across several output voltages.

Published values

ParameterValue
Input voltage1.6 V to 45 V, 50 V absolute maximum
Reference voltage600 mV, 588 mV to 612 mV over temperature, I grade
Output range600 mV to 44.5 V
Output current100 mA, current limit with foldback
Line regulation0.6 mV typical, 3.5 mV maximum
Load regulation0.2 mV typical, 4 mV maximum, 1 mA to 100 mA
ADJ pin bias current15 nA typical, 60 nA maximum, sourced out of the pin
Dropout voltage300 mV typical at 100 mA
Quiescent current40 uA typical, below 1 uA in shutdown
Package8-lead ThinSOT, part marking LTDTF
Thermal resistance57 C/W to 67 C/W junction to ambient, 25 C/W to case
GradeI, minus 40 C to 125 C

Sizing the divider so the reference stays honest

The reference is 600 mV and the ADJ pin draws 15 nA out of the pin, 60 nA at the limit. That current times the bottom resistor adds directly to the set point, so the divider current has to be at least an order of magnitude above it. The vendor's own test condition is 115 kOhm on the bottom and 365 kOhm on top for a 2.5 V output, which is about 5 uA, and that current is additional load on the output that the quiescent current figure does not include. For a 600 mV output the datasheet is explicit that the top resistor should not exceed 62 kOhm, which is the point at which the bias current error and the divider current stop being separable. A 12 V or 15 V output from this part needs a feedforward capacitor from OUT to ADJ, doubled whenever the divider current is doubled, because the divider multiplies reference noise by the same ratio that it sets the output.

What the adjustable body cannot do

Two specifications that the fixed voltage codes carry do not appear on this one. There is no guaranteed load regulation figure tied to an internal divider, because there is no internal divider, and the dropout figure is a typical value with the same production test limit note that applies to the whole ThinSOT body. The adjustable version is also tested with ADJ tied to OUT, which is the 600 mV condition, so a program running at 12 V is outside the exact test condition even though it is inside the guaranteed reference window. None of that is a defect; it is the difference between a part that has a specification and a part that has a reference and a pair of external resistors. Where the regulation budget has to be contractual, the fixed DFN codes carry the guarantee.

Cold start and the shutdown path

The I grade covers minus 40 C at the junction with a real guarantee, which for a 24 V industrial board usually means the part is warm within a minute of power application but has to start cold. Two things help there. The REF/BYP capacitor is discharged in shutdown, so the soft start ramp is identical on every enable rather than depending on how long the rail has been off. And the current limit folds back with input to output differential, so a cold start into a partly discharged bulk capacitor does not sit at the full limit with 20 V across the pass element. The shutdown pin is rated to plus or minus 50 V absolute and its threshold sits well inside a 3.3 V logic swing, so it can be driven directly from a microcontroller pin without a level shift.

Fixed versus adjustable in one file

The seven fixed options are 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V and 15 V, and every one of them is the same die with a different internal divider. Using the adjustable code everywhere simplifies the part number list and complicates the error budget, and using the fixed codes everywhere removes two components and two error terms but multiplies the line items. Which way a file should go depends on volume more than on engineering taste. The family matrix is on the power management cross reference, the second source position for ADI linear parts is described on ADI part second source, and the scheduling side for the ThinSOT body is on the lead time page.