LT3060ITS8-5#TRPBF
Product Specifications
LT3060ITS8-5#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3060ITS8-5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3060ITS8-5#TRPBF: industrial grade 5 V, 100 mA, 45 V input in ThinSOT
The LT3060ITS8-5#TRPBF is the 5 V fixed LT3060 in the 8-lead ThinSOT, tape and reel, in the I grade, which is guaranteed over minus 40 C to 125 C at the junction rather than tested at a single point. Input range is 1.6 V to 45 V, output current is 100 mA, quiescent current is 40 uA and the output sits inside 4.900 V to 5.100 V over line, load and temperature. This is the workhorse code for a 5 V sensor or interface rail on a 24 V industrial board, where the ambient is known and the cold end stops at minus 40 C.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 1.6 V to 45 V, 50 V absolute maximum |
| Output voltage | 5 V fixed, 4.900 V to 5.100 V over temperature |
| Line regulation | 1.5 mV typical, 8.5 mV maximum, 5.55 V to 45 V input |
| Load regulation | 3.7 mV typical, 35 mV maximum, 1 mA to 100 mA |
| Dropout voltage | 300 mV typical at 100 mA |
| Quiescent current | 40 uA typical at no load, below 1 uA in shutdown |
| Output noise | 30 uV RMS, 10 Hz to 100 kHz, 10 nF on REF/BYP |
| Minimum output capacitor | 2.2 uF ceramic, stable with low ESR |
| Package | 8-lead ThinSOT, part marking LTFWH |
| Thermal resistance | 57 C/W to 67 C/W junction to ambient, 25 C/W to case |
| Grade | I, minus 40 C to 125 C, guaranteed over the full window |
Why the I grade is usually the right answer
Textbook industrial cabinets are specified from minus 40 C to 85 C at the air, and a junction that starts 20 C above ambient lands inside the 125 C limit the I grade is written against. The E grade covers 0 C to 125 C with the cold end assured by characterization only, which is fine for office equipment and not fine for a cabinet outdoors. The H and MP grades extend to 150 C at the junction, and their test coverage is what the price difference buys. A buyer who has been quoting the E code into a minus 40 C requirement and passing qualification on good luck has a documentation problem rather than a silicon problem, and moving to the I code is cheaper than a field return.
The derating line above 125 C
The datasheet states plainly that operating lifetime is derated at junction temperatures above 125 C, and that the overtemperature protection lets the junction exceed 125 C during a fault before it acts. For the I grade the practical consequence is that 125 C is the ceiling, not a target, and the thermal arithmetic should aim at 100 C or below. From 24 V to 5 V at 100 mA the part dissipates 1.9 W, which at 67 C/W is a 127 C rise and is not survivable in a 60 C enclosure. From 12 V the figure is 0.70 W and a 47 C rise, which is workable. The gap between those two numbers is why a 5 V rail on a 24 V bus is usually a switching job and why this part belongs on the low differential rails.
Two ThinSOT specifications that are not warranted
Dropout at high current and load regulation on the fixed voltage options are guaranteed for the DFN body and not for the ThinSOT body, because of production test limitations rather than because the parts differ in silicon. The vendor tests the ThinSOT fixed codes the same way as the adjustable version with ADJ tied to OUT. For a 5 V rail with a 100 mV budget this changes nothing. For a program that needs the load regulation number in a qualification document, the equivalent DFN code is the one to buy, and the substitution is a footprint change rather than a drop in.
Holding the rail through a shortage
The same 5 V function exists in the 2 mm DFN as LT3060EDC-5 and LT3060IDC-5, and in the wider temperature grades as HTS8-5 and MPTS8-5. Which of those is a drop in depends on the footprint and on the temperature claim, both of which are tabulated on the power management cross reference. Where the I code has gone short, the split between pin compatible and footprint changing options is set out on pin to pin cross reference and the shortage route itself on the lead time page.