Contact Us

LT1763IS8#TRPBF

Brand: Analog Devices
Analog Devices LT1763IS8#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT1763IS8#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT1763IS8#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT1763IS8#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT1763IS8#TRPBF: the adjustable low noise regulator in the 8 lead SO body, on reel

What this order code is

LT1763IS8#TRPBF is the adjustable member of the LT1763 family in the 8 lead SO body, industrial grade, lead free, on tape and reel. The output is programmed by two external resistors against a 1.22 V reference, the current is 500 mA with 300 mV of dropout, the quiescent current is 30 microamps and the noise is 20 microvolts RMS with a 0.01 microfarad bypass capacitor. Reverse battery protection, reverse current protection, current limit and thermal limit are internal and no external protection diode is needed.

The S8 in the code is the point of this page. The LT1763 is offered in an 8 lead SO and in a 12 lead 4 mm by 3 mm DFN, and the DFN has an exposed pad while the SO does not. The die is the same, the electrical table is the same and the pin count is not: the SO body has to pass its heat through the leads and the copper under them, which makes it the right choice for a board that already has an SO footprint and the wrong choice for a 500 mA rail at a wide input to output difference.

Parameters as published

ItemValue
Output voltageadjustable, 1.22 V to 20 V
Reference1.22 V
Output current500 mA
Dropout at 500 mA300 mV
Input range1.8 V to 20 V
Quiescent current30 microamps, controlled in dropout
Shutdown currentunder 1 microamp
Output noise20 microvolts RMS with a 0.01 microfarad bypass capacitor
Minimum output capacitor3.3 microfarads
Protectionreverse battery, reverse current, current and thermal limit
Body8 lead SO, no exposed pad
Temperature gradeindustrial
Packingtape and reel, lead free

Numbers that decide the application

The thermal question is the one that separates this code from its DFN sibling. The SO body has to get rid of heat through eight leads, and a lead frame in a plastic body that size is a few tens of degrees per watt at best with generous copper. At 0.5 W the junction rise is already substantial, and at 0.85 W, which is 5 V in to 3.3 V out at 500 mA, the part is at the edge of what the body will pass in a warm enclosure. A board that needs the full 500 mA at a 1.7 V input to output difference should be using the DE package, and a board that keeps the SO footprint should be sized for about 250 mA at that difference.

The adjustable output arithmetic is the same as on the DFN member: the output is 1.22 V times one plus the ratio of the two resistors, so 2.5 V needs a ratio of 1.049, 3.3 V needs 1.705 and 5 V needs 3.10. The divider current is a real term against a 30 microamp quiescent current: a 12.4 kilohm upper resistor at 100 microamps is more than three times the part current, so a standby budget that quoted only 30 microamps has to be corrected. Raising the pair to 124 kilohm brings the divider to 10 microamps and leaves the regulator dominant.

Dropout of 300 mV at 500 mA is 0.6 ohm, so the minimum input at any current is the output plus 0.6 ohm times the current plus a margin for the current limit. On a 2.5 V rail that is 2.8 V at full load and 2.53 V at 50 mA, which is why the same regulator that fails on a 2.5 V input at 500 mA works perfectly at 50 mA. The 3.3 microfarad minimum output capacitor is a stability requirement rather than a ripple choice, and the part is stable with ceramic without a series resistor, so the value after dc bias derating is what has to be checked.

Where it fits and where it does not

It fits boards with an existing SO 8 footprint, rails that are not one of the six fixed voltages, and low to medium current analogue supplies where the 20 microvolt noise floor matters. It does not fit a 500 mA rail with a large input to output difference in a warm enclosure, a rail below 1.22 V, or a board where the divider cannot be fitted. The absence of an exposed pad is not a defect, it is a thermal decision that has to be made with the actual dissipation in hand.

Supply and second source questions

The questions we get on this code are about the package, the resistor values already on the board and the grade. Because the electrical table is shared with the DFN member, a substitution between the two looks safe on paper and is safe electrically, but it is not safe thermally, and the direction that fails is the DFN to SO move on a hot board. The members that share the die and the ones that only look similar are listed on the power management cross reference page.

Sourcing notes and next step

We quote this code against the bill of materials and check the four fields that decide whether the line runs: the programmed output, the body, the grade and the reel. Where the exact code is short we will say so rather than move a line from the DFN to the SO body without confirming the dissipation. Send the line items, quantities and required date through the BOM shortage recovery page, and where a second source is being considered on a long life board, the ADI part second source page lists the members that match on the electrical table and the ones that also match on the thermal path. The family list sits on the analog and mixed signal IC page.

Request Quote — In Stock, 100% New & Original, Full Warranty