Contact Us

LT1634ACS8-1.25#PBF

Brand: Analog Devices
Analog Devices LT1634ACS8-1.25#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT1634ACS8-1.25#PBF — Analog & Mixed-Signal ICs | Superb Automation

LT1634ACS8-1.25#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT1634ACS8-1.25#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT1634ACS8-1.25#PBF: a 1.25 V shunt reference on 10 uA and 0.05 percent

The LT1634ACS8-1.25#PBF is the 1.25 V member of the Analog Devices LT1634 shunt reference family, a two-terminal bandgap part trimmed with thin film resistors to 0.05 percent initial accuracy and specified at 10 ppm per degree C maximum drift. The family covers 1.25 V, 2.5 V, 4.096 V and 5 V, and the 1.25 V and 2.5 V versions are also offered in MSOP. Operation down to 10 uA with less than 1 ohm of dynamic impedance is the point of the part: it can be biased from a high value resistor on a rail that has almost no current to spare. The A in the order code is the tighter initial accuracy grade, and the S8 is the SO-8 body. It is a direct performance upgrade for the LM185, LM385, LT1004 and LT1034 where lower power and a guaranteed drift are needed, and it is listed with the converters it usually serves on the analog and mixed-signal IC line card.

What 0.05 percent plus 10 ppm per degree C adds up to

At 1.25 V, 0.05 percent is 625 uV. The drift is 12.5 uV per degree C, so over a 125 degree span from -40 C to +85 C it is 1.5625 mV. The two add to 2.19 mV, which is 0.175 percent of the output, three and a half times the initial figure. Against a 12-bit converter on a 2.5 V range, where one LSB is 610 uV, the whole error is under 4 LSB. Against a 16-bit converter on the same range, one LSB is 38 uV and the drift alone is 41 LSB. The part is a precision shunt reference, not a 16-bit absolute standard.

ParameterVendor figureDerived figure
Initial accuracy0.05 percent625 uV at 1.25 V
Drift10 ppm per degree C max12.5 uV per degree C, 1.5625 mV over 125 degrees
Total over temperatureinitial plus drift2.19 mV, 0.175 percent
Operating current10 uA minimum12.5 uW in the reference
Dynamic impedanceless than 1 ohm1 mA of load moves the output under 1 mV
Output capacitornot requiredstable with capacitive loads

The bias resistor is the real selection problem

A shunt reference has to carry its own minimum current plus the load current, and the resistor feeding it has to supply that at the lowest input voltage. With a 10 uA floor and a 100 uA load, the resistor has to pass 110 uA at the minimum rail. If the rail varies from 5 V to 12 V, the same resistor passes 250 uA at 12 V, and the reference then dissipates 3 mW instead of 1.4 mW. The low dynamic impedance means the output does not move much when the load current changes, which is why the part works from an unregulated supply, but the resistor still has to be sized for the worst case at both ends of the rail.

Where the part earns its price and where it does not

  • Portable meters and calibrators benefit from 10 uA operation, because the reference no longer dominates the standby budget.
  • In a 16-bit absolute measurement the drift is the largest single error after the converter itself, so a system calibration is still needed.
  • The part needs no output compensation capacitor, and it stays stable with a capacitive load, which removes a component and a stability question from the board.
  • The 4.096 V member of the same family divides exactly into a 12-bit full scale of 1 mV per LSB, which is why that voltage exists at all.

Questions buyers ask

Is this a series reference? No, it is a shunt part with two terminals, so it needs an external resistor and it sinks rather than sources current.

Can the 1.25 V version be used on a 2.5 V converter? Yes with a gain of two around it, but the amplifier and its resistors then enter the error budget, and the 2.5 V member of the same family avoids that.

Where a reference is being replaced on an existing board, the substitution route is on how to verify a drop in replacement, and the converter pairings are on the ADC DAC cross reference page.

Request Quote — In Stock, 100% New & Original, Full Warranty