Contact Us

ADP5054ACPZ-R7

Brand: Analog Devices
Analog Devices ADP5054ACPZ-R7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADP5054ACPZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADP5054ACPZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADP5054ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADP5054ACPZ-R7: four buck regulators from a 15.5 V rail in a 7 mm by 7 mm body

What this order code is

ADP5054ACPZ-R7 is a quad buck regulator in a 48 lead 7 mm by 7 mm LFCSP on a reel, and the vendor lists it as recommended for new work. It takes an input from 4.5 V to 15.5 V with no preregulator and produces four rails: channel 1 and channel 2 are 2 A, 4 A or 6 A synchronous bucks that integrate the high side MOSFETs and the low side drivers so that external low side FETs can be used for the current and the efficiency the board needs, and channel 3 and channel 4 are 2.5 A synchronous bucks with both FETs inside.

Channels 1 and 2 can be paralleled into a single 12 A output, and channels 3 and 4 into a single 5 A output, which is what allows one part to serve a processor core, a DDR rail, a 3.3 V rail and an analog rail from a single 12 V input. The switching frequency is adjustable from 250 kHz to 2 MHz with an individual half frequency option per channel, and the part can synchronise to an external clock or output one for the rest of the board.

Parameters as published

ItemValue
Input range4.5 V to 15.5 V
Output accuracyplus or minus 1.5 percent over temperature
Channel 1 and 22 A, 4 A or 6 A, external low side FETs
Channel 3 and 42.5 A, both FETs integrated
Parallel channel 1 and 2single 12 A output
Parallel channel 3 and 4single 5 A output
Switching frequency250 kHz to 2 MHz, half frequency option per channel
Reference noise40 uV RMS at 0.8 V, 10 Hz to 100 kHz
Enable threshold0.811 V precision
Mode selectionforced PWM or power saving
Synchronisationinput or output
Power goodchannel 1 output
Protectionundervoltage lockout, overcurrent, thermal shutdown
Body48 lead LFCSP, 7 mm by 7 mm

Numbers that decide the application

The input ceiling of 15.5 V is the number to check first against a 12 V rail. A regulated 12 V rail at plus or minus 5 percent is 12.6 V and fits, with 2.9 V of margin. An unregulated 12 V adapter can sit at 15 V off load and a 12 V battery rail in a vehicle can see a load dump far above 15.5 V, so the part needs a front end clamp or a different family in those cases. The published maximum is a survival and operating limit, not a suggestion to run at 15.5 V.

Switching frequency and input voltage together set the on time. At 2 MHz and 12 V in, a 1 V output has a duty cycle of 8.3 percent, which is 41 ns of on time, and that is short enough that the gate driver and the inductor's current ripple become the limit. At 250 kHz the same rail has 333 ns of on time and much more ripple, so the frequency choice trades inductor size against efficiency and minimum on time.

6 A at 1 V is 6 W, and at 90 percent efficiency the loss is 0.67 W in a 7 mm square body with the board as its heat sink. That is the number that decides whether the 6 A option is available: the current rating is per channel and the thermal rating is shared, so a 6 A channel 1 plus a 6 A channel 2 plus two 2.5 A channels all at full load is well beyond what the package can remove, and the practical configuration is one or two channels at high current and the rest at a fraction.

The reference noise of 40 microvolts RMS at 0.8 V is 50 parts per million, which on a 16 bit converter with a 12.2 microvolt code is 3.3 codes of output noise if the rail is used as a converter reference. That is why a precision analog rail in the same product normally comes from a linear regulator after one of these channels rather than from the buck directly.

Where it fits and where it does not

It fits processor, FPGA and SoC rails, industrial controller boards, instrumentation and telecom line cards that need four rails from one 12 V input in a small area. It does not fit a 24 V input without a preregulator, and it does not fit an automotive load dump environment without protection. Where the analog section needs low noise, the buck channels feed linear regulators; the buck is the pre regulator and not the final analog rail.

Supply and second source questions

The questions that come back on this code are about the external FETs, the channel pairing and the thermal budget. Channels 1 and 2 need external low side FETs, so the 6 A rating is only reached with the right FET, driver match and inductor, and a bill of materials that lists only the regulator does not describe the power stage. Two channels in parallel share current, and the pairing is fixed by the part, not by firmware. Multi rail regulators that reach 6 A per channel from 15.5 V and parts that stop at 5.5 V are separated on the power management cross reference page.

Sourcing notes and next step

We quote this code against the bill of materials and confirm the fields that decide the reel: channel configuration, body, packing and grade. The 48 lead 7 mm body is the only one in this family, and the application circuit around it, including the FETs and inductors, is part of what has to be sourced with the regulator. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability, and where the exact code is short we will say so rather than propose a lower input voltage part. The wider regulator list sits on the analog and mixed signal IC page.

Request Quote — In Stock, 100% New & Original, Full Warranty