LT1175IST-5#PBF
Product Specifications
LT1175IST-5#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT1175IST-5#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT1175IST-5#PBF: minus 5 V at 500 mA with 45 uA of quiescent current
What this order code is
LT1175IST-5#PBF is the fixed minus 5 V LT1175 in the 5-lead surface mount DD package, in a lead free finish. It is a negative low dropout regulator that sinks up to 500 mA, draws 45 uA of operating current and 10 uA in shutdown, tolerates a reverse output voltage without damage, and offers a user selectable current limit of 200 mA, 400 mA, 600 mA or 800 mA. The family also ships in 8-pin PDIP and SO, in a 3-lead SOT-223 and in a TO-220.
The adjustable current limit is unusual and useful: it is set by a pin rather than by a resistor, so the same part can be a 200 mA regulator on a low power board and an 800 mA part on a board with a big negative rail, and the limit can be chosen to protect a connector or a cable rather than the regulator itself.
Parameters as published
| Item | Value |
|---|---|
| Output voltage | minus 5 V fixed |
| Output current | 500 mA |
| Operating current | 45 uA |
| Shutdown current | 10 uA |
| Selectable current limit | 200, 400, 600, 800 mA |
| Dropout | low dropout, anti saturation pass element |
| Reverse output | tolerated without damage or latch-up |
| Shutdown logic | positive or negative |
| Output capacitor | stable across a wide range of values |
| Protection | current limit, power limit, thermal shutdown |
| Body | 5-lead surface mount DD |
| Packing | lead free |
Numbers that decide the application
Heat is the only real limit on a negative regulator of this size. From minus 12 V to minus 5 V at 500 mA the part dissipates 3.5 W, which in the 5-lead DD package with its tab soldered to copper is feasible and in a small outline body is not. From minus 24 V at the same current it is 9.5 W, which no package in this family will pass. The useful statement is that the input rail, not the current rating, decides whether the part survives: a minus 5.5 V input at 500 mA is 0.25 W, a minus 12 V input at 500 mA is 3.5 W, and the same part covers both if the copper is sized for the second case.
The 45 uA of operating current is 0.394 Ah over a year, and the 10 uA shutdown is 87.6 mAh, so the part can hold a negative rail alive in a battery instrument. That figure is why a switching inverter is not always the right answer for a low current negative rail: an inverter with 85 percent efficiency at 20 mA saves 3 mA of input current and adds an inductor and its switching noise.
The current limit choices are an inrush tool. The 800 mA setting is 60 percent above the 500 mA rating, which is the headroom the part uses to charge a large negative output capacitor at power up without dropping out of regulation, and the 200 mA setting is what protects a small connector or a cable that should never see the full current. The reverse output tolerance means a board that loses its negative rail while the positive rail is still up will not damage this part, which is a common failure mode in bipolar analog systems.
Where it fits and where it does not
It fits a bipolar analog supply in an instrument, a modem or an interface driver, an A to D or D to A negative rail, and any battery product that needs a small negative rail with a microamp budget. It does not fit a rail more negative than about minus 30 V, it does not fit a load above 500 mA, and it does not fit a board that needs a positive regulator, because this part sinks current into the negative rail and cannot source.
Supply and second source questions
Negative regulators are less interchangeable than positive ones, and this family makes it worse by having several packages and an adjustable version under the same base number. The fields that matter are the fixed voltage, the body, the current limit option and whether the shutdown pin is present on the package chosen. A substitute that matches the voltage and the current and moves the current limit to a resistor changes the bill of materials and the board. The regulator families are listed on the power management cross reference page.
Sourcing notes and next step
We quote the code with the body and the packing, and we ask for the negative input rail so the dissipation can be checked before the part is committed. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability. The wider regulator list sits on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty