HMCAD1511TR
Product Specifications
HMCAD1511TR
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMCAD1511TR from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
HMCAD1511TR: 8 bits at 1 GSPS, and why 49.8 dB of SNR is the whole story
What this order code is
HMCAD1511TR is the HMCAD1511 analog to digital converter in the 48-lead 7 mm by 7 mm QFN body, on a reel. It is an 8-bit converter built on a time interleaved architecture that runs one channel at 1000 MSPS, two channels at 500 MSPS each or four channels at 250 MSPS each, with integrated cross point switches that route any of four inputs to any channel, a 1x to 50x digital gain, an internal low jitter clock divider, internal reference circuitry needing no external parts, a 1.8 V supply, 1.7 V to 3.6 V control logic and a serial LVDS output.
The modes are the feature. A single 1 GSPS channel is a digitizer front end for a scope, two 500 MSPS channels are an I and Q pair for a wideband receiver, and four 250 MSPS channels are a multi antenna or multi channel acquisition, all from one part number and one board.
Parameters as published
| Item | Value |
|---|---|
| Resolution | 8 bit |
| Sampling, single channel | 1000 MSPS |
| Sampling, dual channel | 500 MSPS per channel |
| Sampling, quad channel | 250 MSPS per channel |
| Input routing | cross point switches on four inputs |
| Digital gain | 1x to 50x |
| SNR at 1x gain | 49.8 dB |
| SNR at 10x gain | 48.2 dB |
| Power at 1000 MSPS | 710 mW including I/O |
| Start up from sleep | 0.5 us |
| Start up from power down | 15 us |
| Supply | 1.8 V |
| Output | serial LVDS or RSDS |
| Body | 48-lead QFN, 7 mm by 7 mm |
Numbers that decide the application
The quantization limit of an ideal 8-bit converter is 49.9 dB, and the published figure is 49.8 dB at unity gain, so the part is essentially at the floor of its own resolution. That is the right result for an 8-bit converter and it means there is nothing to gain from better processing inside the chip: every decibel of system performance has to come from the clock and the analog front end. 49.8 dB is 7.98 effective bits, so the part delivers its resolution and no more.
The same number sets the clock requirement. To hold 49.8 dB with a 500 MHz input the total aperture jitter has to stay near 1.03 ps, at 250 MHz near 2.06 ps and at 750 MHz near 0.69 ps. A clock oscillator with 1 ps of jitter is therefore the correct class for this converter and a 10 ps part will turn it into a 6-bit converter at high input frequencies. The internal divider is low jitter for that reason, and the single clock source it allows across all modes exists so that a board does not add a second oscillator with its own jitter.
Power is 710 mW at full rate including I/O, which at 1.8 V is 394 mA. A 48-lead QFN at that dissipation needs its thermal pad soldered to a copper area and vias, and the package is 7 mm square, so the copper under it is part of the specification. The serial LVDS output carries the sample stream at eight bits per sample, and at 1 GSPS that is 8 Gb/s of payload, which is split across lanes rather than sent on one pair. The 0.5 us wake from sleep and 15 us from power down are what make burst acquisition practical, and the sleep state is the one to use between captures.
Where it fits and where it does not
It fits a digital oscilloscope, a USB powered instrument, a satellite receiver, a wideband software defined radio and any acquisition that needs giga sample rates with 8 bits. It does not fit a measurement that needs 12 or 14 bits, it does not fit a signal below a few megahertz where a slower converter with more resolution is both cheaper and quieter, and it does not fit a board that cannot supply a low jitter clock or a thermal pad.
Supply and second source questions
Two fields decide substitution: the mode count and the output format. A part with the same 1 GSPS and only one channel cannot serve a dual channel receiver, and a part with a parallel CMOS output instead of serial LVDS changes the pin count, the board area and the FPGA interface. The gain and offset registers are also part specific. The converter families are listed on the converter and multiplexer cross reference page.
Sourcing notes and next step
We quote the code with the body and the packing, and we ask which mode the board uses, because the supply and the clock plan follow from it. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability. The wider converter list sits on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty