HMC998A-Die
Product Specifications
HMC998A-Die
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC998A-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC998A die: 2.2 W at 22 GHz from a 15 V rail at 500 mA
The HMC998A is a gallium arsenide pHEMT distributed power amplifier die covering dc to 22 GHz, with 33.5 dBm of saturated output power, 32.5 dBm at one decibel compression, 14.5 dB of gain and 43 dBm of output third order intercept, from a 15 V supply at 500 mA quiescent. It is an older die in an older document, and the numbers are still competitive: 2.24 W of output with 43 dBm of intercept from a die that is matched to 50 ohm on chip is a lot of linear power for the band.
Published values
| Parameter | Value |
|---|---|
| Frequency range | dc to 22 GHz |
| Saturated output power | 33.5 dBm typical |
| Output power at one decibel compression | 32.5 dBm typical |
| Gain | 14.5 dB typical |
| Output third order intercept | 43 dBm typical |
| Supply | 15 V at 500 mA quiescent |
| Matching | 50 ohm input and output on die |
| Typical application | electronic warfare, electronic countermeasures, radar, test equipment |
| Bond reference | data taken with two 0.025 mm wires of 0.31 mm length |
| Dissipation at saturation | 5.26 W |
Seven and a half watts in, 2.24 W out
A 15 V rail at 500 mA is 7.5 W of DC input, and saturated output is 2.24 W, so 5.26 W is dissipated in the die. That is the whole thermal story of the part: a die that takes 7.5 W and puts 2.24 W into the load has to get rid of 5.26 W through its backside, and the carrier is chosen for that rather than for the radio frequency behaviour, which is already fixed on chip.
The 15 V rail is unusual among the parts in this family and it is an advantage in one way and a problem in another. The advantage is that 500 mA is a modest current for 7.5 W, so the bias network has less resistive loss. The problem is that 15 V is high enough that a sequencing error does real damage, and the gate has to be brought up before the drain every time.
Forty three decibels of intercept at 22 GHz
An intercept 10.5 dB above the compression point is a linear part, which is what makes this die useful in a multi carrier or a wideband instrument chain where several signals share the amplifier. A stage that compresses at 32.5 dBm while its intercept sits at 43 dBm can carry a composite signal well above its single carrier rating before the intermodulation products matter.
The efficiency at that operating point is about 30 percent, which is high for a linear stage. The datasheet gain of 14.5 dB is modest, so a chain that needs 40 dB uses three stages or two plus a gain block, and each of those has its own 5 W of heat to deal with.
Old document, still a live part number
The document revision on file is from 2018 and carries the pre merger Hittite numbering. That does not make the part obsolete, but it does mean the electrical limits are stated in the older format and some of the application notes that went with the original release are not in the current document. Buyers should treat the numbers as the authority and the package and assembly drawings as something to confirm.
For a programme that needs a second position, the die and its packaged equivalents are separate order codes with separate availability. A cross reference check has to compare the die thickness and pad arrangement if the assembly already exists, because a new bond schedule is a new qualification.
Two pages worth reading before a purchase order goes out are the RF power transistor cross reference and defense grade components; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to choose an RF amplifier covers the case where the shortage is already on the line.
Two questions buyers ask
Is 33.5 dBm the linear output rating? No. 33.5 dBm is saturation, 32.5 dBm is the one decibel compression point and 43 dBm is the third order intercept. For a multi carrier signal the intercept figure is the one that sets usable output.
What supply does the die need? 15 V at 500 mA quiescent, with a negative gate applied before the drain. The 7.5 W of DC input leaves 5.26 W to be removed through the backside.