Contact Us

HMC8142

Brand: Analog Devices
Analog Devices HMC8142 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC8142 — Analog & Mixed-Signal ICs | Superb Automation

HMC8142

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC8142 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC8142: 26 dBm at 81 GHz to 86 GHz with a detector on the die

The HMC8142 is an E-band gallium arsenide pHEMT medium power amplifier die covering 81 GHz to 86 GHz with 21 dB of gain, 25 dBm at one decibel compression, 26 dBm saturated, 29 dBm of output third order intercept and 20 percent power added efficiency, from 4 V at 450 mA. It includes a temperature compensated power detector on the die, which is unusual at this frequency and removes the directional coupler that a 26 dBm E-band transmitter would otherwise need. The die measures 3.039 mm by 1.999 mm by 0.05 mm.

Published values

ParameterValue
Frequency range81 GHz to 86 GHz
Gain19 dB minimum, 21 dB typical
Gain variation over temperature0.02 dB per degree
Input return loss12 dB typical
Output return loss8 dB typical
Output power at 1 dB compression22.5 dBm minimum, 25 dBm typical
Saturated output power26 dBm typical
Output third order intercept29 dBm at 12 dBm per tone
Power added efficiency20 percent
Supply4 V on four drains, 450 mA total, 1.8 W of DC
Gate biasVGG1 to VGG4 adjustable minus 2 V to 0 V, minus 3 V absolute maximum
On chip detectortemperature compensated power detector
Die size3.039 mm by 1.999 mm by 0.05 mm
Thermal resistance48.33 degrees per watt, channel to die bottom
Junction temperature175 degrees maximum for a million hours mean time to failure

One point four watts of heat in six square millimetres

4 V at 450 mA is 1.8 W of DC. At the 26 dBm saturated point the output is 398 mW and the quoted efficiency of 20 percent implies about 16 dBm of drive, so roughly 1.4 W becomes heat on a die face of 3.039 mm by 1.999 mm, which is 6.07 square millimetres. That is 0.23 W per square millimetre, high but not extreme for a power die, and the vendor thermal resistance of 48.33 degrees per watt is quoted with a specific die attach epoxy at 20 W per metre kelvin.

That detail is the one to read twice. Forty eight degrees per watt with a 20 W per metre kelvin epoxy is already a 68 degree rise at 1.4 W, so the junction sits 68 degrees above the carrier. A better attach, a sintered silver or a eutectic, lowers that number and buys back junction temperature; a worse one, such as a thick dispensed epoxy with voids, raises it and eats the margin to the 175 degree limit. The 175 degree limit is itself tied to a million hours of mean time to failure, so it is a reliability number rather than a damage threshold.

A detector on the die removes a coupler and adds a calibration

At 85 GHz a directional coupler is a machined or thin film component with its own loss and its own cost, and putting the detector on the die removes both. The detector is temperature compensated, which addresses the main weakness of a diode detector, and it means the transmit level can be monitored without a separate path.

What it does not remove is the calibration. A detector on the die measures a voltage proportional to the output power at the point where it samples, and the relationship between that voltage and the power delivered to the antenna depends on the loss of the following transition and any filter. A module that uses the detector for level control has to be calibrated at the antenna port, not at the die, and the calibration has to be redone if the antenna assembly changes. That is a test cost rather than a component cost, and it is worth quoting separately.

Twenty five dBm of compression with 21 dB of gain means a 4 dBm input

With 21 dB of gain and 25 dBm at one decibel compression, the input at which the part starts to compress is about 4 dBm. That is a comfortable level for a driver and an uncomfortable one for a system that expects to drive the last stage directly from a mixer, because a mixer output of 4 dBm is already at the top of what most E-band mixers deliver. The driver in front of this amplifier therefore needs its own compression point specified, and the cascade has to be checked rather than assumed.

The second consequence is that the input return loss of 12 dB meets a driver whose output match is unlikely to be better than 10 dB. Two mismatches of that size produce a gain ripple of about a decibel across the band, and at 85 GHz that ripple adds to the flatness of the antenna and of the waveguide run. A pad of 2 dB between the driver and this die is often the cheapest way to stabilise the cascade, and the two decibels are recovered by the 21 dB of gain.

For a board that has to keep running while a reel runs out, the RF component sourcing page is where the family alternatives sit, the RF power transistor cross reference is the check list before a substitute goes in, and how to choose an RF amplifier is how a gap is covered without a new line item.

Two questions buyers ask

Does the on chip detector remove the need for a coupler? It removes the coupler from the transmit path. The detector still has to be calibrated at the antenna port, because its reading includes the loss of everything after the die.

What attach does the 48.33 degrees per watt figure assume? A die attach epoxy with a thermal conductivity of 20 watts per metre kelvin. A better attach lowers the junction temperature and a thicker or voided one raises it.