HMC797APM5E
Product Specifications
HMC797APM5E
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC797APM5E from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC797APM5E: DC to 22 GHz, 4 W of DC and a gate that has to be set
The HMC797APM5E is a gallium arsenide pHEMT distributed power amplifier in a 32-lead, 5 mm by 5 mm leadless package, covering DC to 22 GHz with 13.5 dB of gain, 28 dBm at one decibel compression, 29.5 dBm saturated, 39 dBm of output third order intercept and 400 mA from a 10 V supply. Unlike the self biased parts in the same family it has a gate: VGG1 sits at about minus 0.8 V in the published table and is adjusted between minus 2 V and 0 V to reach the 400 mA. The three band slices in the table are not identical, and the top slice is where a link budget built from the headline row comes apart.
Published values
| Parameter | Value |
|---|---|
| Frequency range | DC to 22 GHz, specified in three slices |
| Gain | 12.5 dB typical DC to 12 GHz, 13.5 dB typical above 12 GHz |
| Gain flatness | 0.5 to 0.7 dB within each slice |
| Output power at 1 dB compression | 28 dBm DC to 12 GHz, 27 dBm 12 to 18 GHz, 25.5 dBm 18 to 22 GHz |
| Saturated output power | 29.5 dBm DC to 12 GHz, 29 dBm 12 to 18 GHz, 27 dBm 18 to 22 GHz |
| Output third order intercept | 39 dBm DC to 12 GHz, 37 dBm 12 to 18 GHz, 35 dBm 18 to 22 GHz |
| Noise figure | 3.5 dB DC to 12 GHz, 4 dB 12 to 18 GHz, 6 dB 18 to 22 GHz |
| Supply | 10 V at 400 mA, VGG1 minus 0.8 V typical |
| Gate adjustment range | minus 2 V to 0 V to reach 400 mA |
| Package | 32-lead, 5 mm by 5 mm QFN, 25 square millimetres |
| Matching | 50 ohm input and output, no external matching components |
Four watts in, 0.89 W out, 3.1 W of heat in 25 square millimetres
10 V at 400 mA is 4.0 W of DC, and saturated output at the bottom of the band is 29.5 dBm, which is 0.89 W. The remaining 3.1 W leaves as heat through the exposed pad, across 25 square millimetres of package footprint, which is 0.12 W per square millimetre of board area. The number is lower than a bare die because the package spreads the heat, and it is the board that has to carry it away.
The via field under the pad is the part that is usually under built. At 3.1 W a thermal resistance of 20 degrees per watt from pad to board is a 62 degree rise, which puts a 70 degree board at 132 degrees inside the package. Splitting the dissipation across a larger copper area on the far side of the board is cheaper than adding airflow, and it works because the limiting resistance is the spreading through the board rather than the package.
The gate is set once and then has to stay set
VGG1 at minus 0.8 V is a typical figure for 400 mA, and the adjustment range runs to minus 2 V, which is a wide spread across parts and across temperature. A fixed divider that lands on 400 mA at 25 degrees on the bench will not hold 400 mA on a board at 85 degrees, because a pHEMT at a fixed gate voltage conducts more when it is hot. The current then rises, the dissipation rises, and the loop closes on itself.
The safe sequence is gate first: apply VGG1 at the negative end with the drain off, bring the drain to 10 V, then walk the gate towards 0 V until the drain current meter reads 400 mA. Shutdown runs the other way, gate to the negative end before the drain falls. A supply that brings both rails up together starts the part with the gate at 0 V and the drain at 10 V, which is the one condition the part is not built to survive.
Three slices, and the one that decides the link budget
The headline row is the DC to 12 GHz slice: 28 dBm, 13.5 dB of gain at the top slice, and 3.5 dB of noise figure. Above 18 GHz the compression point falls to 25.5 dBm and the noise figure rises to 6 dB. A system that spans the whole range has to be sized on the 18 GHz to 22 GHz slice, and that is a 2.5 dB power difference and a 2.5 dB noise difference against the number most often quoted.
The positive gain slope from 4 GHz to 20 GHz is mentioned in the description as a feature and behaves as one in a cascade, because it partly cancels the roll off of the stages around it. It also means the input drive that produces compression moves with frequency, so a levelled source is worth having when the part is characterised in a fixture.
Sourcing notes for this family: the RF power transistor cross reference holds the cross references, how to choose an RF amplifier is the pre substitution check, and component lead time solutions is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask
Can the 400 mA be set with a fixed resistor divider? It can be set that way at one temperature, and it will not hold. The gate range runs to minus 2 V across parts, and the drain current rises with temperature at a fixed gate voltage, so a current sense loop or at least a per board trim is needed.
Is 28 dBm available across the full 22 GHz? No. The 28 dBm figure belongs to DC to 12 GHz. The 12 GHz to 18 GHz slice is 27 dBm and the 18 GHz to 22 GHz slice is 25.5 dBm at one decibel compression.