Contact Us

HMC797A-Die

Brand: Analog Devices
Analog Devices HMC797A-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC797A-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC797A-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC797A-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC797A-Die: DC to 22 GHz and 1 W, with a gain slope that is part of the specification

The HMC797A-Die is a gallium arsenide pHEMT distributed power amplifier chip specified from DC to 22 GHz, with 14.5 dB of gain, 28 dBm at 1 dB compression and 40 dBm of output third order intercept from a 10 V supply at 400 mA. It is internally matched to 50 ohm, which is what makes it usable in a multi chip module, and its published gain rises from 3 GHz to 21 GHz rather than being flat.

Published values

ParameterValue
Frequency rangeDC to 22 GHz
Small signal gain14.5 dB typical, 13.5 dB minimum to 18 GHz
Gain flatness0.5 dB to 10 GHz, 0.7 dB from 10 to 18 GHz
Output power at 1 dB compression28 dBm typical, 28.5 dBm to 18 GHz
Saturated output power31 dBm typical
Output third order intercept40 dBm typical
Noise figure3.5 dB typical at the low end, 3 dB from 10 to 18 GHz
Supply10 V at 400 mA
Gate biasVGG1 between -2 V and 0 V to set 400 mA, VGG2 at 3.5 V
Input and output match50 ohm, internally matched
Die size2.89 mm x 1.55 mm x 0.1 mm
Assemblytwo 0.025 mm wire bonds of minimal length, 0.31 mm

The positive gain slope is a system decision

The datasheet says the response has a positive slope from 3 GHz to 21 GHz and presents that as a feature. A rising response is useful when the preceding stage or the cable has a falling response, because the two cancel. It is a problem when the chain is otherwise flat, because the output level then depends on where in the band the signal sits.

For a multi octave electronic warfare channel that means an equaliser is still needed, and the equaliser is easiest to place at the input where the level is low. For a narrow band radar channel the slope is irrelevant and only the gain at the operating frequency matters, which is why the datasheet quotes the figure in three band segments.

Four watts of dc into 4.5 square millimetres

10 V at 400 mA is 4 W, and the die is 2.89 mm by 1.55 mm, or 4.5 square millimetres. That is about 0.9 W per square millimetre which has to leave through the backside of a 100 micrometre thick chip, so the die attach and the carrier are the thermal specification. A eutectic attach to a copper tungsten carrier and a carrier screwed to a heatsink is the normal route.

At 1 dB compression the output is 28 dBm, or 631 mW, so about 3.4 W is heat at that point. At 14.5 dB of gain, 28 dBm out corresponds to 13.5 dBm in, and a source capable of 20 dBm will drive the part well past compression. The chip has no protection against that.

Why the bond is part of the specification

The published data is taken with two 0.025 mm wire bonds 0.31 mm long. At 22 GHz a 0.31 mm wire is several tenths of a nanohenry, which is tens of ohms of reactance in series with a 50 ohm port, and the vendor's own measurement includes that. A module that uses longer bonds, or ribbon instead of wire, measures a different response at the top of the band and the difference is not correctable in the module.

The practical consequence is that the assembly drawing has to specify the bond geometry and the bonding machine settings, and two assembly houses using the same die can produce modules that differ by a decibel at 22 GHz. That is worth knowing before a second assembly source is qualified on the strength of a first article measurement.

Where the die version earns its place

A packaged amplifier at 22 GHz has a launch, a lid and a lead frame in the radio frequency path, and each of those adds a discontinuity. A die in a module removes them, so the die version is chosen when the module has to meet a return loss or a gain flatness that a package cannot, or when several functions share one sealed housing.

The cost is that the die is not a part a board assembly line can place. It needs a chip and wire process, an inspection step and a rework route that most contract assembly houses do not have. For a programme without that capability the packaged member of the family is the practical choice.

For a board that has to keep running while a reel runs out, the amplifier cross reference is where the family alternatives sit, defense grade components is the check list before a substitute goes in, and vendor consolidation is how a gap is covered without a new line item.

Two questions buyers ask

Does the HMC797A-Die need a negative supply? It needs a positive drain supply of 10 V and a gate bias, with VGG1 adjustable between -2 V and 0 V to set 400 mA and VGG2 at 3.5 V. The gate bias has to be present before the drain is applied.

Is the gain flat across the band? No. The response has a positive slope from 3 GHz to 21 GHz as published, and the gain is quoted in three band segments. A flat chain needs an equaliser, normally at the input.