LTM8055IY
Product Specifications
LTM8055IY
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8055IY from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8055: A 36 V Buck-Boost Regulator That Arrives as a Component
The LTM8055 is a 36 V input, 8.5 A buck-boost micromodule regulator in a 15 mm by 15 mm by 4.92 mm ball grid array. Inside the package are the switching controller, the power switches, the inductor and the support components, so what a board has to add is a resistor to set the switching frequency, a divider to set the output voltage, and input and output capacitors. It regulates any output between 1.2 V and 36 V from any input between 5 V and 36 V, which means the output can sit above, below or equal to the input without a mode change, and it reaches 97.5 percent efficiency at the operating points the datasheet calls out: 12 V at 3 A from 6 V in, 12 V at 6 A from 12 V in, and 12 V at 8.5 A from 24 V in.
What the module removes from the schedule
A discrete four-switch buck-boost regulator is a project. The controller and the FETs have to be placed and routed so that the hot loops stay small, the inductor has to be chosen against ripple and saturation over the input range, the current sense has to be laid out so the ramp is not corrupted by switching noise, and the loop has to be compensated for a plant whose behaviour changes with the input to output ratio. The module has done all of that inside a shielded package, and what remains on the board is a divider, a frequency resistor and capacitors. On a schedule, that is a block of work that disappears from the critical path, and on a small board it is the difference between fitting and not fitting.
Values at a glance
| Parameter | Value | Note |
|---|---|---|
| Topology | Four switch buck-boost | Output above, below or equal to input |
| Input range | 5 V to 36 V | 40 V absolute maximum |
| Output range | 1.2 V to 36 V | Set by a resistor divider |
| Output current | 8.5 A peak at 24 V in, 12 V out | 3 A at 6 V in into 12 V, 6 A at 12 V in |
| Efficiency | Up to 97.5 percent | At the 24 V to 12 V operating point |
| Switching frequency | 100 kHz to 800 kHz selectable | Synchronisation input accepts 200 kHz to 700 kHz |
| Current control | Adjustable input and output average current limits | With analogue current monitor outputs |
| Paralleling | Supported for higher output current | Current mode sharing between modules |
| Package | 15 mm by 15 mm by 4.92 mm BGA | Standard surface mount assembly, RoHS compliant |
Input and output current limits as a feature, not a protection
The two average current limits are adjustable with resistors or by injecting a voltage, and the matching monitor outputs report the actual input and output current as an analogue voltage. In a battery charger that turns the module into a constant current source with a defined taper, and in a solar application it allows the input current to be held at the maximum power point rather than letting the panel collapse. In a system with a limited upstream supply, the input current limit stops the module from pulling the rail down when a load step arrives, which is a behaviour a voltage mode regulator cannot offer. Using those pins as part of the control strategy rather than as a fault response is the difference between a supply that survives a brownout and one that trips.
The two versions and the thermal question
The LTM8055 has internal loop compensation and the LTM8055-1 brings the compensation node out, which allows the loop to be tuned when the output capacitor is unusual or when a fast transient response is needed at the cost of phase margin. Choosing between them is a question of whether the fixed compensation suits the output capacitor on the board. The thermal side is where a module this size has to be checked: 8.5 A at 12 V is 102 W of output, and even at 97 percent efficiency the loss is over 3 W in a package that relies on the board for heat spreading. The copper under and around the BGA is part of the thermal path, and a board with a small thermal pad will run the module hotter than the datasheet curves assume.
Industrial, battery and solar supplies
High power battery operated devices, industrial control, solar powered voltage regulation and solar battery charging are the applications the part is specified for, and they share a requirement: the input voltage moves over a wide range and the output has to stay regulated through it. A 12 V rail fed from a battery that runs from 9 V to 28 V is the classic case, and a buck-boost is the only single stage that covers it. Where the input never crosses the output, a plain buck or boost is smaller and cheaper, and the honest comparison is against the two single mode alternatives rather than against another buck-boost. The module's advantage appears at the crossing point and in the schedule, not in every application.
Procurement and second source
Modules are single sourced by construction: the inductor and the controller are inside the package, so there is no pin compatible alternative from another vendor, and a supply interruption has to be covered with stock rather than with a substitute. The power management cross reference lists the regulators that cover the same input and output window, component lead time solutions covers the buffer stock approach for single sourced parts, and the incoming checks on ball grid array coplanarity and moisture level are set out in the incoming inspection plan.