Contact Us

HMC659-Die

Brand: Analog Devices
Analog Devices HMC659-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC659-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC659-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC659-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC659 die: 2.4 W of DC for 28.5 dBm from DC to 15 GHz

The HMC659 is a gallium arsenide pHEMT distributed power amplifier covering DC to 15 GHz with 19 dB of gain, 35 dBm of output third order intercept, 27.5 dBm at one decibel compression and 28.5 dBm saturated, from 8 V at 300 mA. The vendor document on file is the ceramic packaged order code, so the electrical table describes the amplifier rather than the die, and the die is the same part without the package transitions. For a buyer the useful split is between the numbers that belong to the amplifier and the ones that belong to the body it arrives in.

Published values

ParameterValue
Frequency rangeDC to 15 GHz, specified in three bands
Gain19 dB typical DC to 6 GHz, 18 dB 6 to 11 GHz, 17 dB 11 to 15 GHz
Gain flatnessplus or minus 0.7 dB, 0.4 dB and 0.7 dB across the bands
Gain variation over temperature0.015, 0.019 and 0.022 dB per degree
Noise figure3.0 dB typical DC to 6 GHz, 2.5 dB 6 to 11 GHz, 3.5 dB above
Input return loss20 dB, 18 dB and 17 dB
Output return loss19 dB, 20 dB and 15 dB
Output power at 1 dB compression26.5 dBm, 27.5 dBm and 26.5 dBm typical
Saturated output power28.0 dBm, 28.5 dBm and 27.5 dBm
Output third order intercept35 dBm, 32 dBm and 29 dBm
Supply8 V at 300 mA, 2.4 W of DC
Gate biasVGG1 adjusted for 300 mA, VGG2 at 3 V typical

The gain does not fall with frequency the way the band table suggests

Gain is 19 dB in the low band, 18 dB in the middle and 17 dB in the top, which is a two decibel tilt across fifteen gigahertz, and the flatness inside each band is tighter than that. A distributed amplifier is usually described as flat by construction; here the flatness is per band and the tilt is between bands, so a system that sweeps continuously through 6 GHz and 11 GHz crosses two specification boundaries. A sweep measured at 5 GHz and 12 GHz is not a sweep of the whole part.

The second order effect is that the noise figure has a dip in the middle band, 2.5 dB against 3.0 dB below and 3.5 dB above. That is the band where the input line behaves best, and it is the band to use if a receiver has any freedom about where it sits. Choosing an intermediate frequency inside 6 GHz to 11 GHz buys half a decibel of system noise figure compared with the low band for no extra cost.

Two point four watts of DC and a die with no paddle to help it

8 V at 300 mA is 2.4 W of DC. At 28.5 dBm saturated the output is 708 mW, so 1.69 W becomes heat, and on a die that heat has only the backside to leave through. The die area of this family is a few square millimetres, so the heat flux is in the region of 0.4 W per square millimetre, which is high enough that the attach is the part of the assembly that decides the junction temperature.

A void free attach under the whole die face is the minimum, and a copper molybdenum carrier is the usual choice because its expansion matches the gallium arsenide and its conductivity is high enough to spread the heat into the housing. Epoxy attach is possible for a laboratory build and is not appropriate at 1.7 W in a sealed module, because the thermal conductivity of a filled epoxy is an order of magnitude below a eutectic or a sintered silver joint.

Thirty five decibels of intercept is what a multicarrier system buys

The output third order intercept of 35 dBm in the low band is seven decibels above the compression point, which is a wide linear region for a distributed amplifier. For a system carrying several carriers at once the intercept sets the intermodulation level: two tones at 15 dBm each are 20 dB below the 35 dBm intercept, so the third order products land near 55 dB below the carriers.

That margin is what allows the part to sit after a lossy multiplexer without a driver in front of it. Once the top band is reached, the intercept falls to 29 dBm and the same two tones at 15 dBm each are only 14 dB below it, so the products are 28 dB down and a system that needed 50 dB of spurious free range no longer has it. The band of operation again decides whether this amplifier is linear enough.

For a board that has to keep running while a reel runs out, the RF power transistor cross reference is where the family alternatives sit, how to choose an RF amplifier is the check list before a substitute goes in, and the RF component sourcing page is how a gap is covered without a new line item.

Two questions buyers ask

Is the noise figure good enough for a first stage? 2.5 dB in the 6 GHz to 11 GHz band is usable as a first stage, and 3.5 dB above 11 GHz is not. The part is normally a driver or a pre driver rather than a receiver front end.

Does the amplifier need a negative supply? Yes, VGG1 sits below the source to set 300 mA, and VGG2 at 3 V is a second bias point that must be present before the drain current is set.