Contact Us

HMC637BPM5E

Brand: Analog Devices
Analog Devices HMC637BPM5E is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC637BPM5E — Analog & Mixed-Signal ICs | Superb Automation

HMC637BPM5E

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC637BPM5E from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC637BPM5E: a self biased DC to 7.5 GHz 1 W amplifier in a 5 mm package

The HMC637BPM5E is a gallium arsenide pHEMT cascode distributed amplifier in a 32-lead 5 mm x 5 mm LFCSP, specified from DC to 7.5 GHz with 15.5 dB of gain, 28 dBm at 1 dB compression and 39 dBm of output third order intercept. It is self biased from a single 12 V rail at 345 mA, with optional bias pins that a buyer can either use or leave alone.

Published values

ParameterValue
Frequency rangeDC to 7.5 GHz
Small signal gain15.5 dB typical
Gain flatness0.5 dB typical
Output power at 1 dB compression28 dBm typical
Output third order intercept39 dBm typical
Noise figure3.5 dB typical
Supply12 V at 345 mA, self biased
Optional bias controlVGG1 for quiescent current, VGG2 for IP2 and IP3
Input and output match50 ohm, internally matched
Package32-lead LFCSP, 5 mm x 5 mm, 25 mm squared

What self biased means at the board level

Self biased means the part sets its own gate voltage from the drain rail, so a single 12 V supply and a handful of decoupling capacitors are enough to make it amplify. The two gate pins are brought out so that a user who wants to trim the quiescent current or to trade second order intercept against third order intercept can do so, but a board that leaves them open still works.

The difference matters at procurement time. A part that needs a sequenced negative gate supply before the drain is applied has a turn on order that has to be enforced, and a mistake destroys the device. This one does not have that failure mode, which is why it appears in test equipment and in military programmes where the board may be hot plugged.

The power budget and where the heat goes

12 V at 345 mA is 4.14 W of dc input. At 1 dB compression the output is 28 dBm, which is 631 mW, so the dc to radio frequency conversion at that point is about 15 percent and roughly 3.5 W leaves as heat. A 5 mm x 5 mm package with a 25 square millimetre footprint has to pass that into the board, and the ground paddle under the part with a via field is the only path.

At 15.5 dB of gain, 28 dBm out corresponds to 12.5 dBm in. A bench source that can deliver 20 dBm will therefore drive the part more than 7 dB past compression, and a first test that sweeps input power without a limiter is how these parts are lost. The output is also not protected against an open load, and a distributed amplifier into an open can oscillate.

Band coverage and the DC to 7.5 GHz claim

A distributed amplifier reaches DC because the input and output are artificial transmission lines rather than tuned matching networks. That is why this part is used where a signal of interest sits near DC, such as a baseband driver or a pulse generator, and why it is not the right part for a narrow band application where a tuned amplifier would give more gain for less current.

The gain flatness of 0.5 dB over the band is the number that matters in a wideband chain, because a flat response is what keeps a multi-octave system's error vector magnitude from varying with frequency. A narrow band part with higher gain usually has a gain slope that has to be equalised somewhere else.

Where it sits against the die version

The packaged part is specified to 7.5 GHz while the older die version of similar name is specified to 6 GHz with 14 dB of gain, 29 dBm at compression and a 12 V, 400 mA bias. The package brings surface mount assembly, a controlled 50 ohm launch and a repeatable thermal path, at the cost of a slightly lower frequency ceiling.

For a programme that needs the extra octave, the die remains an option with ribbon bonds and a carrier. For everything else the packaged part removes the assembly uncertainty, and the difference in gain between the two is within the tolerance a chain budget usually carries.

Sourcing notes for this family: the amplifier cross reference holds the cross references, defense grade components is the pre substitution check, and the pin to pin cross reference is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Can the HMC637BPM5E be run from 5 V? No. The specified supply is 12 V at 345 mA and the self bias network is referenced to that rail. The optional gate pins adjust quiescent current, not the supply voltage.

Does it need a negative gate supply at power up? No. It is self biased, so the drain rail alone brings it into operation. Sequencing a negative gate supply is only relevant if the optional VGG pins are driven externally.