Contact Us

HMC586LC4B

Brand: Analog Devices
Analog Devices HMC586LC4B is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC586LC4B — Analog & Mixed-Signal ICs | Superb Automation

HMC586LC4B

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC586LC4B from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC586LC4B: 4 to 8 GHz From a Single 5 V Rail, With the Tuning Curve as the Real Spec

The HMC586LC4B is a wideband voltage controlled oscillator with the resonator, the negative resistance device, the varactor and a buffer amplifier all inside a 4 x 4 mm package. It tunes from 4 GHz to 8 GHz, delivers about +5 dBm, runs from a single +5 V rail at 55 mA, and needs no external resonator or tuning stub. The four numbers that decide whether it fits a radio are not the ones on the first line of the data sheet: they are the phase noise at 10 kHz and 100 kHz, the pushing figure, and the tuning sensitivity across the band.

The published numbers, and the one that is usually ignored

ParameterValueConsequence
Frequency range4 GHz to 8 GHzOne part covers both the 6 GHz and the 7 GHz bands
Output power+5 dBm typical, +2 dBm minimumEnough for a passive mixer only with a following amplifier
Phase noise-75 dBc/Hz at 10 kHz, -100 dBc/Hz at 100 kHzSets the far out noise of the whole loop
Tuning voltage0 V to +18 VThe charge pump has to reach 18 V, so a 5 V pump is not enough
Supply current55 mA at +5 V275 mW, no negative rail required
Pushing40 MHz/V10 mV of ripple on the 5 V rail is 400 kHz of deviation

Why pushing matters more than phase noise on a real board

A pushing figure of 40 MHz/V means the supply is a tuning port. Any switching regulator that feeds the 5 V rail and is not followed by a low noise post regulator will modulate the oscillator at the regulator's switching frequency, and that shows up as spurs either side of the carrier. Two things follow. The oscillator rail should be fed from a linear regulator with a good rejection at the switching frequency, and the decoupling should be at the pin, not at the other end of the board. A 100 kHz switcher needs rejection at 100 kHz, which is where many low dropout parts are already losing their loop gain.

The tuning curve is not a straight line

Sensitivity across the 0 V to 18 V range varies by a factor of several, which is normal for a wideband oscillator with a single varactor. A phase locked loop whose filter is calculated for the middle of the band can be stable there and marginal at the low end, where the sensitivity is highest. The practical answer is to check the loop at three tuning voltages rather than one, and to keep the loop bandwidth low enough that the worst case gain still leaves phase margin.

Drift is a locking problem, not a trimming problem

The frequency drift rate is quoted at 0.8 MHz per degree C. Over a 25 C to 85 C excursion that is roughly 48 MHz of open loop movement, which is more than the band of the modulation in most links. Such a part is never used open loop; the number is there so that the loop can be given enough capture range at cold start. Boards that report a channel that will not lock when cold usually have a loop filter sized for the room temperature tuning sensitivity only.

Second source and replacement notes

When this oscillator is out of stock or has gone past its last order date, the substitution has to match the band edges, the tuning voltage ceiling and the output power, in that order; package compatibility comes last because a 4 x 4 mm body can be reworked more easily than a loop filter can be recalculated. The RF component sourcing page lists the oscillator family, the obsolete RF part replacement page covers end of life cases, and volume and lead time questions go through RF procurement.