Contact Us

HMC562-Die

Brand: Analog Devices
Analog Devices HMC562-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC562-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC562-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC562-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC562-Die: 2 GHz to 35 GHz, and two different power figures on the same page

The HMC562-Die is a gallium arsenide pHEMT distributed driver amplifier chip covering 2 GHz to 35 GHz with 12.5 dB of gain from an 8 V supply at 80 mA, dc blocked and internally matched to 50 ohm. Its datasheet carries two sets of power figures that do not agree, and a buyer writing a link budget has to know which pair to use.

Published values

ParameterValue
Frequency range2 GHz to 35 GHz
Small signal gain12.5 dB typical, 9.5 dB minimum from 2 to 15 GHz, 7 dB from 27 to 35 GHz
Output power at 1 dB compression, feature list18 dBm
Output power at 1 dB compression, general description12 dBm
Output third order intercept, feature list27 dBm
Output third order intercept, general description19 dBm
Supply8 V at 80 mA
Gate biasVGG between -2 V and 0 V to set 80 mA
Input and output match50 ohm, internally dc blocked
Die size3.12 mm x 1.42 mm x 0.1 mm

The two power figures

The feature list on the first page states 18 dBm at 1 dB compression and 27 dBm of output intercept, and the general description on the same page states 12 dBm and 19 dBm. Both are in the vendor's own document, and neither is a typographical slip that can be resolved from the page alone.

Until a measurement settles it, the cautious route is to budget with the lower pair. A chain that assumes 18 dBm and 27 dBm and gets 12 dBm and 19 dBm has lost 6 and 8 dB of margin, which in a driver stage is the difference between meeting a spurious requirement and failing it.

Gain that falls with frequency

12.5 dB typical at the bottom, 9.5 dB minimum to 15 GHz and 7 dB minimum from 27 to 35 GHz describes a distributed amplifier doing what a distributed amplifier does. The gain per section is roughly constant and the line loss rises with frequency, so the response falls, and the same physical effect moves the compression point down with it.

For a wideband chain the falling gain is usually corrected at the input, where the level is low and an equaliser costs little in noise figure. Correcting at the output costs power and linearity, which is why the placement of the equaliser is a real decision rather than a detail.

640 mW of dc for a driver

8 V at 80 mA is 640 mW. At 12 dBm of output that is 16 mW, so the conversion is about 2.5 percent, and at 18 dBm it is 63 mW, or about 10 percent. Either way the die is dissipating most of its input power, and a die of 4.4 square millimetres at 0.6 W is comfortable on a grounded carrier with a conductive epoxy attach.

The 80 mA has a maximum of 100 mA in the same table, which is the number to use for the supply. The gate is adjusted between -2 V and 0 V to set the current, so the setting is per die rather than per board, and a module built to a fixed gate voltage from a previous batch will not necessarily draw the same current.

Where it is used

Military and space, test instrumentation and fibre optics are the listed applications, and all three want a small, wideband gain block with a known bias point rather than maximum power. The 3.12 mm by 1.42 mm die is small enough that several can sit in one module without a thermal problem.

The dc blocked ports are worth noting for an optical application, because a photodiode bias network is where a dc coupled amplifier causes trouble. Here the blocking is inside the die, which removes one component per port from the module.

Buyers usually arrive at the amplifier cross reference to find the family alternatives, then use defense grade components to confirm a substitute before it is fitted; how to verify a drop in replacement is the routine for a part that has already stopped shipping.

Two questions buyers ask

Is the output power 18 dBm or 12 dBm? The feature list says 18 dBm at 1 dB compression and the general description on the same page says 12 dBm. Budget with 12 dBm until the module is measured.

Does it need dc blocking on the ports? The die I/Os are internally dc blocked and matched to 50 ohm, so external blocking capacitors are not required for the radio frequency path. The bias lines still need bypass capacitors.