HMC463-Die
Product Specifications
HMC463-Die
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC463-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC463 die: 60 mA, two gate pins and 3.05 mm of gallium arsenide
The HMC463 is a gallium arsenide pHEMT distributed amplifier die covering 2 GHz to 20 GHz with 14 dB of gain, 2.5 dB of noise figure at 10 GHz and 19 dBm of output power at one decibel compression, from a single 5 V supply at 60 mA. The die measures 3.05 mm by 1.29 mm by 0.1 mm, is matched to 50 ohm at both ports, and carries a second gate, VGG2, that works as a gain control over about 10 dB. Every published figure was taken with the chip in a 50 ohm fixture connected by 0.025 mm wire bonds of minimal length, 0.31 mm, which is the detail that decides whether a replacement assembly reproduces the table.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 2 GHz to 20 GHz |
| Gain | 12 dB minimum, 15 dB typical 2 to 6 GHz; 12 dB minimum, 14 dB typical 6 to 20 GHz |
| Gain flatness | plus or minus 1.0 dB from 2 to 6 GHz, plus or minus 0.15 dB from 6 to 20 GHz |
| Gain variation over temperature | 0.015 dB per degree typical, 0.025 dB per degree maximum |
| Noise figure | 3.0 dB typical 2 to 6 GHz, 2.5 dB typical 6 to 18 GHz, 3.5 dB typical 18 to 20 GHz |
| Input return loss | 12 dB, 15 dB and 14 dB across the three bands |
| Output return loss | 11 dB, 12 dB and 10 dB across the three bands |
| Output power at 1 dB compression | 19 dBm typical 2 to 6 GHz, 16 dBm 6 to 18 GHz, 14 dBm 18 to 20 GHz |
| Saturated output power | 21 dBm, 20 dBm and 19 dBm across the three bands |
| Output third order intercept | 31 dBm, 28 dBm and 26 dBm across the three bands |
| Supply | 5 V at 60 mA typical, 80 mA maximum |
| Gate bias | VGG1 minus 0.9 V typical, adjustable minus 1.5 V to minus 0.5 V for 60 mA |
| Gain control | VGG2 second gate, about 10 dB of range |
| Die size | 3.05 mm by 1.29 mm by 0.1 mm |
| Thermal resistance | 48.6 degrees per watt, channel to die bottom |
| Channel temperature | 175 degrees maximum |
The two gate pins, and the one nobody ties off
VGG1 sets the drain current. The published operating point is 60 mA at 5 V with VGG1 at minus 0.9 V, and the vendor states the adjustment range as minus 1.5 V to minus 0.5 V, which is wide because the threshold voltage of a pHEMT spreads several hundred millivolts across a wafer. A fixed divider that lands on 60 mA on one die will not land there on the next, so either the gate is trimmed per assembly or the drain current is measured and recorded at test.
VGG2 is the second gate and it is easy to leave floating on a first article. The absolute maximum table allows it from VDD minus 9 V to plus 2 V, which means at 5 V of drain it can sit anywhere between minus 4 V and plus 2 V without damage, and the gain control range of about 10 dB is obtained by moving it inside that window. If a board ties VGG2 to ground by default, the amplifier still works, but the one control that would let a receiver survive a strong nearby signal is now unavailable and the pin cannot simply be driven later without checking the bias point again.
Why 14 dB stays flat to a fifth of a decibel across an octave and a half
A distributed amplifier absorbs the transistor capacitances into artificial transmission lines, so gain per stage is traded for bandwidth. That is why 14 dB is available across more than three octaves and why the flatness figure is plus or minus 0.15 dB between 6 GHz and 18 GHz while the low band, from 2 GHz to 6 GHz, is only held to plus or minus 1.0 dB. The low band is where the input and output line impedances stop behaving as intended, and it is the band a link budget should not assume the mid band flatness for.
The on chip match stops at the bond pad, so the assembly is part of the radio frequency path. A 0.025 mm gold wire 0.31 mm long is roughly 0.25 nanohenry, which is about 1.6 ohm at 1 GHz and 35 ohm at 22 GHz, and the published figures were taken with that geometry. A longer loop, a ribbon instead of a round wire, or a single bond where the fixture used two changes the match at the top of the band and shows up as a tilt rather than as a failed part, which is the hardest kind of variation to catch at incoming inspection.
0.3 W of DC, 79 mW out, and what is left for the die to carry
5 V at 60 mA is 0.3 W of DC input. At the 19 dBm compression point the output is 79 mW, so 0.22 W becomes heat, and the die face is 3.05 mm by 1.29 mm, which is 3.93 square millimetres. That is 0.056 W per square millimetre, a modest number that a copper molybdenum carrier or a sintered attach handles without difficulty, and the 48.6 degrees per watt channel to die bottom means a 0.22 W dissipation is a 10.7 degree rise.
The figure that matters for derating is the other one in the document: 1.85 W of continuous dissipation at an 85 degree base with a 20.6 mW per degree derate above it. That ceiling is reached only if the output is driven hard into a mismatch, and a 2:1 load can push the dissipation up while the measured output power falls, which is why an isolator or a pad in front of the next stage protects the die from a fault that the power meter never shows.
For a board that has to keep running while a reel runs out, the RF component sourcing page is where the family alternatives sit, the LNA selection guide is the check list before a substitute goes in, and how to choose an RF amplifier is how a gap is covered without a new line item.
Two questions buyers ask
Does the HMC463 need a negative supply rail? It needs a negative gate voltage with respect to the source, and VGG1 sits at about minus 0.9 V for 60 mA. On a single positive rail board that means a small charge pump or a divider referenced to a negative node, and the gate has to be applied before the drain or the part conducts uncontrolled.
Is the 10 dB gain control a level control? It is an AGC input. Moving VGG2 changes the bias of the first stage, so the noise figure moves with the gain, and 2.5 dB is the figure only at the nominal setting.