HMC441LH5
Product Specifications
HMC441LH5
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC441LH5 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC441LH5: 22 dBm at 23 percent efficiency from a single 5 V rail
The HMC441 is a gallium arsenide pHEMT medium power amplifier covering 6 GHz to 18 GHz with 15.5 dB of gain, 22 dBm of saturated output at 23 percent power added efficiency and 5 dB of noise figure, from a single 5 V supply drawing 90 mA to 115 mA. Optional gate bias on VGG1 and VGG2 allows the gain, the output power and the dissipation to be traded against each other. As die it measures 0.94 mm by 0.94 mm, and the backside is both radio frequency and direct current ground, which is what makes the small die practical to mount.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 6 GHz to 18 GHz |
| Gain | 15.5 dB typical, 13 dB minimum |
| Saturated output power | 22 dBm at 14 GHz to 15.5 GHz |
| Output power at 1 dB compression | 18.5 dBm to 20 dBm depending on band slice |
| Power added efficiency | 23 percent at saturation |
| Output third order intercept | 29 dBm to 32 dBm depending on band slice |
| Noise figure | 4.5 dB to 5 dB |
| Supply | 5 V, 90 mA to 115 mA with the gate left open |
| Gate bias | VGG1 and VGG2, optional |
| Die size | 0.94 mm by 0.94 mm by 0.1 mm |
| Applications | point to point radio, VSAT, local oscillator driver, electronic warfare |
The efficiency figure and the current figure are measured differently
22 dBm is 158 mW of output. At 23 percent power added efficiency the DC input has to be 0.69 W, which at 5 V is 138 mA. The published supply current of 90 mA to 115 mA is taken with the gate left open, which is the self biased point, not the driven point at saturation. Both numbers are correct and they describe two different states.
That matters when a 5 V rail is being sized. A budget built on 115 mA gives 0.58 W, and the part will ask for 138 mA during a saturated transmission, so the rail droops by whatever the source impedance allows. The droop reduces the output power, which reduces the efficiency, which raises the current again. The rail has to be sized on the driven figure with margin.
A 0.94 mm die that has to get rid of half a watt
At saturation the dissipation is 0.69 W of DC input less 0.158 W of output, which is 0.53 W on a die face of 0.88 square millimetres. That is 0.6 W per square millimetre, higher per unit area than the larger distributed parts in the family, and it is why the backside ground matters twice: it is the radio frequency reference and the thermal path.
The small size is the feature. Eight of these fit in the area one 3 mm by 3 mm die would take, which for a phased array or a multi channel upconverter is the whole argument. It also means the assembly tolerance is tighter, because the bond length relative to the 0.94 mm die edge is a larger fraction of the geometry than it would be on a bigger part.
What the optional gate bias buys
Leaving VGG1 and VGG2 open gives the self biased operating point and the simplest board. Bringing them out allows the gain to be reduced, the output power to be trimmed and the dissipation to be cut when the full output is not needed. In a system that transmits intermittently, lowering the quiescent current between transmissions is worth more than any efficiency improvement at saturation.
The gate also allows a per channel trim in an array, which is how the amplitude taper across an antenna is usually set when the beam forming is done at radio frequency. That is a real use for the pins, and it is the reason a board that starts with the gate open often ends up using it once the array is characterised.
Where a customer needs a second position on this part, the RF component sourcing page is the starting point, one stop RF supply sets out the checks a substitution has to pass, and how to choose an RF amplifier is the short lead time route we quote against.
Two questions buyers ask
Is 23 percent efficiency the number to use for a power budget? It applies at saturation, where the DC input is 0.69 W and the current about 138 mA at 5 V. Backed off for linear operation the efficiency falls and the dissipation stays close to the quiescent figure, so the power budget has to cover both states.
Can the gain be adjusted in circuit? Yes, through VGG1 and VGG2. The pins are optional, and leaving them open gives the self biased point. Using them allows the gain and the dissipation to be traded, at the cost of a second bias voltage per channel.