HMC349ALP4CETR
Product Specifications
HMC349ALP4CETR
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC349ALP4CETR from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC349ALP4CETR: a nonreflective SPDT specified from 100 MHz to 4 GHz
The HMC349ALP4CETR is a GaAs single pole double throw switch covering 100 MHz to 4 GHz with 62 dB of isolation to 2 GHz, 1 dB of insertion loss, a 53 dBm input third order intercept and a 34 dBm input compression point. It is a nonreflective part, which is the detail that decides whether it can sit in front of a live amplifier.
Published values
| Parameter | Value |
|---|---|
| Configuration | SPDT, nonreflective, 50 ohm |
| Frequency range | 100 MHz to 4 GHz |
| Isolation | 62 dB to 2 GHz |
| Insertion loss | 1.0 dB to 2 GHz |
| Input IP3 | 53 dBm |
| Input P1dB | 34 dBm |
| Control | enable and control lines, positive logic |
| Package | 4 mm by 4 mm QFN style surface mount |
Sixty two decibels of isolation is what a shared antenna needs
Sixty two decibels at 2 GHz means a 30 dBm transmit signal appears at 32 dBm below a milliwatt in the receive branch, which is below the noise floor of most receivers. That is the number that allows one antenna to serve a transmit and a receive path through a single switch rather than two cascaded ones.
Isolation falls with frequency in every switch of this type. A board that works at 2 GHz has to be checked at 4 GHz, where the published curve is typically ten decibels worse, and where a receiver with a low noise front end will notice.
Nonreflective means the off port is terminated
A nonreflective switch presents 50 ohms on the port that is switched out. That matters when the off port is connected to an amplifier output: a reflective switch would leave the amplifier looking into an open or a short, and the resulting mismatch shows up as gain ripple and, at high power, as damage.
The price is that the termination dissipates power. A 10 W signal switched into the internal load is a thermal question for a 4 mm package, so a high power transmit path still needs a switch rated for the power, not just one with good isolation.
Linearity at 53 dBm, and what that buys in a radio
An input intercept of 53 dBm with a 34 dBm compression point means the switch can sit directly after a power amplifier of a few watts without being the limiting element. In a receive path the same linearity protects against a strong blocker, which is the case that decides a cellular front end.
The surrounding parts have to match. A switch at 53 dBm behind a 30 dBm amplifier is not the limit, but the connector, the trace and the filter usually are, so the intercept figure is a ceiling rather than a system number.
Second position on the switch family
For a board that has to keep running while a reel runs out, the pin to pin cross reference is where the family alternatives sit, how to verify a drop in replacement is the check list before a substitute goes in, and vendor consolidation is how a gap is covered without a new line item.
Two questions buyers ask
What does nonreflective mean here? The port that is switched out is terminated in 50 ohms instead of presenting an open or a short, so an amplifier on that branch sees a matched load and the gain stays flat.
How much power can it carry? The compression point is 34 dBm and the intercept 53 dBm at low level. The termination dissipates the power of the switched out branch, so a high power path needs a part rated for that power.