HMC326MS8G
Product Specifications
HMC326MS8G
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC326MS8G from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC326MS8G: 26 dBm Saturated at 3.0 to 4.5 GHz From a 5 V Rail and an MSOP8
The HMC326MS8G is a GaAs InGaP heterojunction bipolar driver amplifier for the 3.0 GHz to 4.5 GHz band. It provides 21 dB of gain, +26 dBm of saturated output power and better than 40 percent power added efficiency from a single +5 V supply, in an eight lead MSOP with an exposed base. It is a narrowband part with internal matching, built for microwave radios, broadband radio systems and wireless local loop drivers, and it is one of the few parts in this power class that fits an eight lead package without an external matching network.
The thermal path is the real limit, not the gain
At +26 dBm the RF output is 0.4 W. At 40 percent power added efficiency the DC input is close to 1 W, which at 5 V is roughly 200 mA, and the difference, about 0.6 W, leaves the package as heat. In an MSOP8 that heat has one route out: the exposed base, the vias underneath it, and the copper on the other side of the board. A board with four vias in the pad and a solid ground plane under it will hold the junction temperature; a board with a single via and a thin pour will not, and the symptom is a part that works on the bench and folds back inside the enclosure.
| Parameter | Value | Effect |
|---|---|---|
| Frequency range | 3.0 GHz to 4.5 GHz | Narrowband, matched internally |
| Gain | 21 dB | Two stages of this part give 42 dB before filtering |
| Saturated output | +26 dBm | 0.4 W, the figure the thermal path is sized for |
| Power added efficiency | Better than 40 percent | Sets the DC current at saturation |
| Output intercept | +36 dBm | Governs the back off point for a multi carrier signal |
| Supply | +5 V, with a Vpd control pin | Power down when the channel is idle, at very low control current |
The compression curve sits under the saturation figure
With a saturated output of +26 dBm, the 1 dB compression point falls a little below it, and multichannel operation has to be backed off from there by the peak to average ratio plus a margin. A single carrier can be run close to saturation because the peak is the average; four carriers with a 6 dB peak to average ratio need the mean power 8 to 10 dB below the compression point before the intermodulation products fall back into the receive band.
The power down pin is not a mute
The Vpd pin controls the bias of the amplifier, and with the control at ground the part draws a fraction of its running current. That is enough to take the channel quiet, but it is not a switch: the RF path is still connected, with a different impedance, so a receiver sharing the antenna will see a change in return loss when the transmitter is put to sleep. Where isolation matters, an actual switch belongs in front of the amplifier.
Second source and grading
The part comes in two order codes, the HMC326MS8G and the HMC326MS8GE, which differ only in the packing and the lead finish, so the two can be mixed on one board but not on one bill of materials without a note. Replacements from other vendors in the same band usually need an external match, which changes the board far more than a package change does. The amplifier cross reference page compares the driver family by band and power, the RF power transistor cross reference page covers the higher power devices that follow it, and the RF procurement page carries the current lead time.