HMC1082LP4E
Product Specifications
HMC1082LP4E
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC1082LP4E from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC1082LP4E: 26 dBm Saturated Across 5.5 to 18 GHz From a 220 mA Bias
The HMC1082LP4E is a gallium arsenide pseudomorphic high electron mobility transistor driver amplifier covering 5.5 GHz to 18 GHz, with 22 dB of gain, an output intercept of +35 dBm, an output compression point of +24 dBm and a saturated output of +26 dBm at 26 percent power added efficiency. It runs from a single +5 V supply with a bias current of 220 mA and includes a temperature compensated power detector on chip. Its practical attraction is the bandwidth: more than three to one, in a 4 by 4 mm package, with no external matching.
The bias current and the saturated current are not the same number
At +26 dBm the radio frequency output is 0.4 W. At 26 percent power added efficiency, the direct current input at that point is about 1.5 W, which at 5 V is 300 mA, well above the 220 mA quoted for the small signal bias. Both numbers are correct and they describe different operating points, but a supply sized for 220 mA and a thermal path sized for the same figure will both be short. The regulator has to deliver the saturation current, and the copper under the package has to remove the difference between 1.5 W in and 0.4 W out.
The published figures
| Parameter | Value | Note |
|---|---|---|
| Frequency range | 5.5 GHz to 18 GHz | Gain falls to 20.5 dB minimum at the top of the band |
| Gain | 22 dB typical | Flatness held across the band by internal matching |
| Output compression | +24 dBm | Drops to about +23.5 dBm above 17 GHz |
| Saturated output | +26 dBm at 26 percent efficiency | The thermal case is this point, not the bias point |
| Output intercept | +35 dBm | Two tones at +12 dBm each |
| Bias | +5 V at 220 mA, gate bias set between -2 V and 0 V | The gate pin is a bias input, not a control input |
The on chip detector is temperature compensated, which is why it is useful
An uncompensated diode detector drifts with temperature by about 2 millivolts per degree, which over a 125 degree range is 250 millivolts and enough to make a power control loop lose its set point. The detector in this part is compensated, so its output tracks radio frequency power rather than junction temperature. It is still a relative measurement with a part to part spread, so it serves a control loop well and a calibrated power meter poorly.
Two ways to use it, and the level plan changes
As a driver for a higher power stage, it runs several dB below compression and the detector monitors the drive level. As the final stage in a short link, it runs at compression and the detector monitors the output. The second use is where the thermal margin disappears: an amplifier run at compression with a modulated signal spends part of every symbol above the average, and the junction temperature tracks the peak envelope rather than the mean power. In a radar or a burst system, the thermal calculation has to use the pulse conditions, not the average.
Availability and second source
Parts with this bandwidth and this output power have few drop in replacements, because the internal matching is specific to the band and the package. A substitute usually means a narrower band part plus a band switch, which is a board change rather than a component change. The amplifier cross reference page lists the driver family by band and power, the how to choose an RF amplifier page covers the gain and compression trade, and defence programmes are covered on the defense grade components page.