HMC1022A-Die
Product Specifications
HMC1022A-Die
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC1022A-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC1022A die: dc to 48 GHz at 24 dBm, and an obsolete status to plan around
The HMC1022A is a gallium arsenide pHEMT distributed amplifier die covering dc to 48 GHz, with 24 dBm of saturated output power, 22 dBm at one decibel compression, about 12 dB of gain and 32 dBm of output third order intercept, from 10 V at 150 mA. The die is 2.82 mm by 1.50 mm by 0.1 mm and matched to 50 ohm. The document that carries these figures is marked obsolete by the vendor, which changes the buying conversation more than any of the electrical numbers do.
Published values
| Parameter | Value |
|---|---|
| Frequency range | dc to 48 GHz, specified in three slices |
| Saturated output power | 24.5 dBm typical, dc to 16 GHz, 23.5 dBm to 36 GHz, 21 dBm to 48 GHz |
| Output power at one decibel compression | 22 dBm typical |
| Gain | about 12 dB, 9.5 dB minimum |
| Output third order intercept | 35 dBm typical low band, 32 dBm mid band, 29 dBm high band |
| Supply | 10 V at 150 mA |
| Gate bias | VGG1 adjusted between minus 2 V and 0 V for 150 mA, VGG2 at 4.5 V |
| Thermal resistance | 37 degrees per watt, channel to die bottom |
| Maximum dissipation | 1.76 W at 85 degrees, derated 27 mW per degree above |
| Die size | 2.82 mm by 1.50 mm by 0.1 mm |
What obsolete means for a part that is still on the shelf
The vendor document carries an obsolete marker, which in practice means the die is no longer recommended for new work while remaining available through distribution and broker channels for a period that nobody publishes. For a programme that already has it in a qualified assembly the question is not whether it is obsolete but how long the remaining stock covers the build plan and what the alternative is.
The alternative has to be checked on three levels rather than one. Electrical: gain of about 12 dB, 24 dBm of saturation, dc to 48 GHz. Mechanical: a 2.82 mm by 1.50 mm die with a specific pad arrangement and 0.1 mm thickness. Assembly: wire bond length and count at input and output, because the die is matched on chip and the bonds are part of the match. A part that matches two of the three is not a replacement.
The thermal numbers are the ones to copy into the model
37 degrees per watt from channel to die bottom is a high figure by the standards of later parts, and it is published because the die is small and thin. At 10 V and 150 mA the DC input is 1.5 W, which with the 37 degree path is a 55 degree rise from die bottom to channel before any carrier is counted. The maximum continuous dissipation of 1.76 W at 85 degrees, derated by 27 mW per degree, is the limit that follows from that.
This is why the part is used at 24 dBm rather than pushed harder. The channel temperature limit of 150 degrees, the 37 degree per watt path and a 1.5 W DC input together leave very little room, and an application that needs more than 24 dBm needs a different device rather than a higher supply voltage.
Three band slices and the 48 GHz claim
The dc to 48 GHz headline is true and the numbers behind it are not constant. Saturation falls from 24.5 dBm in the lowest slice to 21 dBm in the highest, and the intercept falls from 35 dBm to 29 dBm. A system that uses the part at 45 GHz is working with the weakest slice and should quote from it.
The gain also has a positive slope from 10 GHz to 35 GHz as published, which is a property of the distributed arrangement rather than a defect. Systems that need flat gain across the band have to equalise it, and systems that use a slice of the band get a nearly flat response inside that slice.
The pages that answer this most often are obsolete RF part replacement for the family alternatives, the obsolete part cross reference hub for the acceptance test, and the RF component sourcing page for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Is this part still available? The vendor document is marked obsolete, so availability depends on remaining distribution stock rather than on current production. Any plan that needs it beyond the next build should treat it as a last time buy.
What would a replacement have to match? About 12 dB of gain and 24 dBm of saturation from dc to 48 GHz, the same die footprint and pad arrangement for the existing assembly, and the same bond wire geometry, because the input and output are matched on chip.