ADPA7006AEHZ
Product Specifications
ADPA7006AEHZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADPA7006AEHZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADPA7006AEHZ: 29 dBm from a 6 mm leadless package with a built in detector
The ADPA7006AEHZ is the packaged form of the 18 GHz to 28 GHz amplifier, in a 16-terminal, 6 mm by 6 mm ceramic leadless chip carrier with a heat sink. It delivers up to 29 dBm saturated, 29 dBm at one decibel compression and up to 23 dB of gain with 39 dBm of output third order intercept, from 5 V at 800 mA, and it brings an integrated power detector out to a pin. It is the smallest packaged part in this family that still delivers 29 dBm, which puts it in the space where a buyer is choosing between a 6 mm package and a connectorised module.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 18 GHz to 28 GHz, specified as two slices |
| Saturated output power | up to 29 dBm typical |
| Output power at one decibel compression | up to 29 dBm typical |
| Gain | up to 23 dB typical |
| Output third order intercept | up to 39 dBm typical |
| Supply | 5 V at 800 mA quiescent |
| Package | 16-terminal, 6 mm by 6 mm LCC_HS |
| Extras | integrated power detector, 50 ohm input and output |
| Typical gate voltage | minus 0.68 V for 800 mA |
| Dissipation at saturation | 3.2 W |
Three point two watts in a six millimetre package
5 V at 800 mA is 4.0 W of DC input against 0.79 W of saturated output, so 3.2 W is dissipated continuously. A 6 mm leadless carrier with a heat sink pad moves that comfortably into a board with a via field, and the limit is the board rather than the package: a two layer laminate with a small pad under the part will run 40 degrees above ambient and the bias point will drift with it.
The gate voltage that sets 800 mA has a typical value of minus 0.68 V and a range that runs from about minus 1.5 V upwards, so a fixed divider cannot be trusted across a production lot. The usual arrangement is a bias controller or a current sense loop, and on a 6 mm footprint the controller is often larger than the amplifier.
Detector on a pin, and what it is good for
The detector is temperature compensated and follows the envelope. On a continuous wave link it reads the average and does the job of a coupler and a diode. On a pulsed system the sample has to fall inside the pulse, which means the loop has to be synchronised to the pulse train rather than filtered with a long time constant.
Because the detector is inside the package it sees the output after the internal matching, so it reports the power at the output pin rather than at an antenna port. That is the right place for a level loop and the wrong place for a calibrated radiated power measurement, where the antenna and cable losses still have to be accounted for separately.
Choosing between this and the die
The die version of the same amplifier is 2.750 mm by 1.805 mm and carries 0.63 W per square millimetre, so it needs a carrier and an attach process. The packaged part is 6 mm square, has a quoted thermal path, and can be placed by any surface mount line. For volumes under a few thousand units the package is almost always the cheaper route once the die attach and wire bond steps are counted.
Above that the die starts to win on cost and on loss at 28 GHz, where the package transition costs about a decibel. A programme that is close to its link budget at the top of the band needs the die, and a programme that needs a second source quickly needs the package.
Sourcing notes for this family: the pin to pin cross reference holds the cross references, how to verify a drop in replacement is the pre substitution check, and component lead time solutions is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask
Does the 16-terminal package need a special board? It needs a via field under the heat sink pad and a ground plane under the part. The radio frequency pins are matched to 50 ohm, so the board is a controlled impedance trace rather than a matching network.
Can a fixed gate divider hold the 800 mA quiescent point? Not across a production lot, because the typical gate voltage of minus 0.68 V varies part to part and with temperature. A current sense loop or a bias controller is the reliable route.