ADPA7004-Die
Product Specifications
ADPA7004-Die
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADPA7004-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADPA7004 die: 24 dBm from 40 GHz to 75 GHz on a 2.94 mm by 3.32 mm chip
The ADPA7004 in die form is a gallium arsenide pHEMT amplifier for the 40 GHz to 75 GHz band, with 24 dBm of saturated output power, 22 dBm at one decibel compression, 18.5 dB of gain and 31 dBm of output third order intercept, from 3.5 V at 550 mA. The die measures 2.940 mm by 3.320 mm by 0.05 mm with 20 dB of input return loss and 22 dB of output return loss between 45 GHz and 75 GHz. Above 40 GHz the die thickness, the bond wires and the ground return stop being assembly details and become the matching network.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 40 GHz to 75 GHz |
| Gain | 18.5 dB typical, 45 GHz to 75 GHz |
| Output power at one decibel compression | 22 dBm typical |
| Saturated output power | 24 dBm typical |
| Output third order intercept | 31 dBm typical |
| Input return loss | 20 dB typical |
| Output return loss | 22 dB typical |
| Supply | 3.5 V at 550 mA, quiescent current split across four drain pairs |
| Typical gate voltage | minus 0.4 V for 550 mA |
| Die size | 2.940 mm by 3.320 mm by 0.05 mm |
Four drain pairs, one quiescent current
The 550 mA quiescent current is the sum of four sections, VDD1, VDD2, VDD3 and VDD4, each with an A and a B side, and the gate is adjusted to reach it. In an assembly this means four decoupling points rather than one, and each has to be close to its own pad, because at 60 GHz a via that is a few tenths of a millimetre away is a significant impedance in the drain return.
The DC input is 3.5 V at 550 mA, which is 1.93 W, against 0.25 W of saturated output. So 1.67 W is dissipated, spread over 9.76 square millimetres at 0.05 mm thickness. The 0.05 mm substrate is chosen for the radio frequency behaviour and it also means the die cannot spread heat sideways, so the attach under the four sections is the whole thermal path.
Why 22 dB of output return loss is a gift at these frequencies
A 22 dB return loss is a 1.17 voltage standing wave ratio, which is about as close to a matched load as a packaged transition gets. That is unusual at 75 GHz and it means the interface to the next component can be a short well controlled line rather than a tuned transition. It also means the part tolerates a load that is not perfect, which a 10 dB output match would not.
The 20 dB input return loss is equally useful because the driver at those frequencies is often an attenuator or a mixer output, and both are sensitive to the load they see. Keeping the input match at 20 dB keeps the level flat when the driver changes state, which is what a sweep test checks.
Die thickness and bond length are in the specification
At 60 GHz a 0.025 mm bond wire of 0.3 mm length is about 0.25 nanohenry, which is 94 ohm of reactance. Two in parallel halve it. The data sheet values are taken with short bonds, so the difference between one wire and two at the output is a change in match that shows up as gain ripple. Assembly houses that build at these frequencies work to a written bond schedule, and a substitute part with a different pad arrangement needs a new one.
The 0.05 mm thickness sets the handling and the attach. It also sets the ground inductance: the source of every transistor on the die returns through the backside, and a void in the attach is an inductor in that return, which costs gain and shifts the match. Vacuum solder or sintered attach with a verified void percentage is the usual process.
Sourcing notes for this family: the RF component sourcing page holds the cross references, obsolete RF part replacement is the pre substitution check, and one stop RF supply is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask
Is the part matched to 50 ohm on die? Yes, at input and output, with 20 dB and 22 dB of return loss between 45 GHz and 75 GHz. The bond wires remain part of the match and have to follow the assembly schedule.
What is the supply arrangement? 3.5 V at a total 550 mA quiescent, split across four drain pairs, each needing its own decoupling close to the die. The gate is set for the quiescent current and the typical value is minus 0.4 V.