ADP7118AUJZ-R7
Product Specifications
ADP7118AUJZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADP7118AUJZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADP7118AUJZ-R7: The 5-Lead TSOT Has No Soft Start Pin, Whatever the Data Sheet Features Say
The ADP7118 is a 20 V, 200 mA low noise regulator with 11 uV rms of output noise, rejection of 88 dB at 10 kHz falling to 50 dB at 1 MHz, 200 mV of dropout at 200 mA, 50 uA of quiescent current and a 2.7 V to 20 V input range. The features list includes user programmable soft start, but the small print attaches it to the LFCSP and SOIC bodies. The AUJZ suffix is the 5-lead TSOT, so this order code has no soft start pin, no sense pin and no power good: it is the smallest member of the family and it is the one that cannot be sequenced by a capacitor.
What the five pins actually give
Input, ground, enable, output and the feedback node on the adjustable version. That is enough for a quiet rail that comes up with the rest of the board, and not enough for a rail that has to ramp in a defined order or track another supply. A board that needs soft start with this noise and this input range has to move to the 6-lead LFCSP or the 8-lead SOIC, and moving means a new footprint, so the choice is made before the first copper is cut and not at the bill of materials. The publishable noise figure of 11 uV rms applies to the fixed options of 5 V or less and is independent of the output voltage.
| Item | Published value | Consequence |
|---|---|---|
| Input range | 2.7 V to 20 V | Usable directly on a 12 V or 15 V rail |
| Output current | 200 mA | Small analogue load, not a system rail |
| Dropout at 200 mA | 200 mV typical | 3.3 V output needs 3.5 V in |
| Noise | 11 uV rms | 0.14 of a 16-bit step on 5 V |
| Rejection | 88 dB at 10 kHz, 50 dB at 1 MHz | 1 V of ripple becomes 3.2 mV at 1 MHz |
| Quiescent current | 50 uA typical | 0.44 Ah over a year, from a 20 V rail |
Rejection falls with frequency, and that is the whole story
Eighty eight dB at 10 kHz turns 1 V of ripple into 40 uV, which is below the noise floor of the part. At 1 MHz the same 1 V becomes 3.2 mV, which is above it, so a switching converter running at 2 MHz is the case where this regulator stops being a filter and starts being a follower. The usual arrangement is a ferrite bead or a small inductor ahead of the regulator, chosen so that the switching frequency sits above the corner, and then the 11 uV noise figure is what reaches the load. The 2.2 uF ceramic output capacitor is a stability requirement and also sets the high frequency output impedance.
Adjusting above the set point
Sixteen standard voltages between 1.2 V and 5.0 V exist, with 1.2 V adjustable, 1.8 V, 2.5 V, 3.3 V, 4.5 V and 5.0 V available from stock and the rest by special order. Every fixed output can be adjusted upward with an external divider, which is how a 5 V part becomes 6 V, and the divider changes the noise gain so the noise rises with the amount of adjustment. The enable pin is a precision threshold, so a divider on it gives a programmable undervoltage lockout without an external comparator, which is the one sequencing function this 5-lead body does support.
Second sourcing a 200 mA low noise rail
When this code is short, the replacement has to match the 20 V input rating and the 5-lead pinout, and a 6 V part with the same noise and current is not a substitute in a 12 V socket. The power management cross reference page covers the family, the pin to pin cross reference page covers the footprint, and lot checks follow the incoming inspection plan.