ADP3300ARTZ-3
Product Specifications
ADP3300ARTZ-3
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADP3300ARTZ-3 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADP3300ARTZ-3: the anyCAP regulator that stays stable with any output capacitor
The ADP3300ARTZ-3 is a 50 mA low dropout regulator in a 6-lead SOT-23 that runs from 3.0 V to 12 V and needs only 0.47 uF on the output to be stable. The feature that separates it from a generic 50 mA regulator is the anyCAP behaviour: it stays stable with any capacitor type and any ESR, including multilayer ceramic, so a board that changes the output capacitor for cost or availability does not start oscillating.
Published values
| Parameter | Value |
|---|---|
| Output current | 50 mA |
| Supply range | 3.0 V to 12 V |
| Accuracy at 25 C | 0.8% |
| Accuracy over temperature, line and load | 1.4% |
| Dropout at 50 mA | 80 mV typical |
| Output capacitor | 0.47 uF, any type, any ESR |
| Shutdown current | 1 uA |
| Temperature range | -40 C to +85 C ambient |
| Package | 6-lead SOT-23 |
| Extras | Noise reduction pin, error flag output, thermal and current limiting |
Stability with any capacitor is the sourcing feature
Most low dropout regulators specify a narrow window of output capacitance and ESR, and a substitute capacitor outside that window turns a working rail into an oscillator that looks fine on a meter and fails in the field. A part that is stable with any capacitor removes that class of failure from the build, which on a long life industrial board matters more than a few milliamps of quiescent current.
The 0.47 uF value is small enough that a ceramic part in an 0603 body is sufficient, and the part has a noise reduction pin that takes a small capacitor to lower the output noise when the rail feeds an analogue block.
12 V input on a 50 mA regulator
A 12 V input with a 3.3 V output dissipates 0.435 W at the full 50 mA, which in a 6-lead SOT-23 is close to the limit at 85 C ambient. The data sheet works this through for a 3.3 V output and 8 V input and arrives at an ambient limit around 85 C, so a 12 V input at full load needs either a lower load current or a copper area under the package. This is the one calculation that decides whether the part can be used at the top of its input range.
Error flag and sequencing
The error flag goes active when the output falls out of regulation, which is useful on a board with several rails where a brown out on this one has to be reported rather than discovered later. The shutdown pin takes the part to 1 uA, so a rail that is not needed in a standby mode can be turned off from a microcontroller pin without an extra load switch.
The pages that answer this most often are the power management cross reference for the family alternatives, how to reduce component cost for the acceptance test, and BOM shortage recovery for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Does the ADP3300 work with a 10 uF ceramic output capacitor? Yes, it is stable with any capacitor type and value above the minimum. A larger output capacitor improves the load transient at the cost of a longer rise time at start up.
What does the output voltage list look like? The family covers several fixed voltages including 3.0 V, 3.3 V and 5.0 V, and the suffix in the order code carries the voltage. The suffix has to be matched character by character before a reel is accepted.