ADP1877ACPZ
Product Specifications
ADP1877ACPZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADP1877ACPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADP1877ACPZ: two synchronous buck channels at 200 kHz to 1.5 MHz in a 5 mm package
The ADP1877ACPZ is a dual output synchronous buck controller with the drivers integrated, rated for more than 25 A per channel, running from 2.75 V to 14.5 V and setting an output anywhere from 0.6 V to 90 percent of the input. The 180 degree phase shift between the two channels is the defining feature: it halves the input ripple current and lets a set top box or a printer supply keep both rails inside one input capacitor bank.
Published values
| Parameter | Value |
|---|---|
| Topology | Dual output synchronous buck controller, integrated drivers |
| Input voltage range | 2.75 V to 14.5 V |
| Output voltage range | 0.6 V to 90% of VIN |
| Output current | Greater than 25 A per channel |
| Switching frequency | 200 kHz to 1.5 MHz, programmable |
| Phase relationship | 180 degrees between channels |
| Output accuracy | 0.85% from -40 C to +85 C, 1.5% to 125 C junction |
| Light load | Pulse skip mode |
| Extras | Integrated boost diodes, power good with internal pull up, soft start, current sense gain adjustment |
| Protection | Overvoltage, overcurrent, thermal overload, input UVLO |
| Package | 32-lead LFCSP, 5 mm x 5 mm |
The integrated drivers set the practical current
A controller with integrated drivers still depends on the external MOSFETs for the current it can deliver, and the 25 A per channel figure assumes a power stage sized for it. The gate charge of the chosen FET is what limits the switching frequency: a large FET with low RDSON and 60 nC of gate charge will not switch cleanly at 1.5 MHz, so the frequency range and the current rating are not available at the same time on the same board. Choosing the FET for the frequency first and the current second is the order that works.
Flex mode and light load efficiency
Pulse skip keeps efficiency up when the load falls to a few milliamps by skipping switching cycles instead of holding the frequency. On a standby rail that is the difference between passing an energy budget and missing it. The side effect is a wider output ripple at light load, which matters on a rail feeding an analogue section, so the mode is a system decision, not a default.
What to compare before accepting a substitute
The output accuracy over temperature, the phase shift between channels and the presence of the integrated boost diodes are the three items that change with a substitute controller. A part without integrated boost diodes needs two external diodes and two extra nodes on the board, which turns a chip swap into a board change.
Sourcing notes for this family: the power management cross reference holds the cross references, component lead time solutions is the pre substitution check, and vendor consolidation is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask
Is the ADP1877 a pin replacement for the ADP1823? No. Both are dual buck controllers in a 32-lead LFCSP, but the supply range, the current sensing scheme and the tracking function differ, so the pin functions have to be compared individually before any swap.
How is the current limit set? Through the current sense gain and the sense resistor or RDSON sensing network on each channel, as described in the data sheet. The limit is set per channel, so one rail can be set tighter than the other.