ADM809SARTZ-REEL7
Product Specifications
ADM809SARTZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM809SARTZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADM809SARTZ-REEL7: A 17 Microamp Supervisor That Decides When the Processor May Run
The ADM809SARTZ-REEL7 is a microprocessor supervisory circuit in a 3 lead SOT-23. It holds a push-pull active low reset output for at least 140 ms after the supply crosses the reset threshold, keeps that output valid down to 1 V of supply, and draws 17 uA. Seven threshold options cover 2.5 V, 3 V, 3.3 V and 5 V rails. It is the smallest part on a board and the one that decides whether the processor starts at all.
The threshold, the hysteresis and the glitch filter
The S grade in this order code sits in the 3 V family, at about 2.93 V, which leaves 0.37 V or 11 percent of margin on a 3.3 V rail. That margin is the space in which the rail may dip during a load step without the processor being reset. Too little margin and a normal transient resets the product, too much and the processor runs below its specified minimum voltage before the supervisor reacts. The comparator also carries built in glitch immunity, so a fast transient shorter than the internal filter does not produce a reset pulse, which is what separates this part from a plain comparator with a reference.
What the published figures convert to
| Parameter | Published figure | What it means on a board |
|---|---|---|
| Supply current | 17 uA | 149 mAh over a year, less than the self discharge of a small cell |
| Reset assertion | Valid down to 1 V of supply | The processor is held in reset during the whole power down ramp, not just at the start |
| Reset period | 140 ms minimum, 240 ms typical | Long enough for a 3.3 V rail with a 10 ms rise time and a crystal that needs 5 ms |
| Threshold options | Seven, covering 2.5 V to 5 V rails | One part family covers every rail on the board without a divider |
| Threshold in the S grade | About 2.93 V | 11 percent margin on a 3.3 V rail, so a 0.3 V transient does not reset the product |
| Output stage | Push-pull, active low | No pull-up resistor, and a defined level while the rail is still rising |
| Glitch immunity | Built in | Fast transients on the rail do not produce spurious resets |
| Accuracy over temperature | Specified over the full range | The threshold does not move enough at 85 C to turn a 5 percent margin into 2 percent |
| Package | 3 lead SOT-23 or SC70 | The smallest supervision solution that needs no external components |
| Reset output drive | Push-pull, both directions | Can drive a processor reset pin and a peripheral at the same time |
Checks before accepting a cross reference
- Match the threshold to the rail, not to the part number family. A 4.63 V option on a 3.3 V rail never releases the processor.
- Check whether the output is push-pull or open drain. Firmware that expects open drain with a wired or bus will be shorted by a push-pull part.
- Compare the reset timeout minimum. A part specified at 1 ms will release a slow rising rail before the oscillator starts.
- Confirm the behaviour below 1 V. Parts that stop asserting below 1.2 V allow the processor to run with an undefined state during power down.
- Verify the glitch filter. Without one, a switching transient on the rail appears as a reset on every load step.
Where this part is used
Microprocessor and microcontroller boards, industrial controllers, intelligent instruments, portable equipment and automotive body modules. It is also used as a brown-out detector on a secondary rail where the main processor supervises itself but a sensor rail does not.
Questions buyers ask
Does it need an external capacitor? No. The part is complete in three leads and the reset timing is internal.
Can two supervisors be wired together? With push-pull outputs, no. Two push-pull parts driving the same node fight each other. Use one supervisor per rail or an open drain part for a wired OR.
What happens if the rail never reaches the threshold? The output stays asserted and the processor stays in reset, which is the intended behaviour for a rail that has failed.
Sourcing notes and next step
Supervisors sit with the rest of the analog catalogue on the analog and mixed signal index. Boards that pair a supervisor with a processor usually start the search from the MCU cross reference page, and when a build is short the options are described in the BOM shortage recovery page. Confirm the rail voltage, the required timeout and the output type and we will quote the correct threshold grade rather than the nearest part number.
Request Quote — In Stock, 100% New & Original, Full Warranty