ADM7171ACPZ-3.0-R7
Product Specifications
ADM7171ACPZ-3.0-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM7171ACPZ-3.0-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADM7171ACPZ-3.0-R7: One Amp, Five Microvolts of Noise and 42 Millivolts of Dropout
The ADM7171ACPZ-3.0-R7 is a 1 A CMOS low dropout regulator that runs from 2.3 V to 6.5 V, produces a fixed 3.0 V output, and combines 5 uV rms of output noise with 60 dB of supply rejection at 100 kHz, 42 mV of dropout at 500 mA and a 1.5 us transient response to a 1 mA to 500 mA load step. It is aimed at the rails that feed converters, precision amplifiers, phase locked loops and clocking devices, which are exactly the rails where a switching converter alone is not acceptable.
Noise in parts per million, not microvolts
Five microvolts rms on a 3.0 V output is 1.67 ppm. At 18 bits on a 3 V span one code is 11.4 uV, so the regulator noise is 0.44 of a code. That is the number that decides whether a 1 A rail can feed an 18 bit converter without a second stage: a regulator with 40 uV of noise would contribute 3.5 codes and would force a post filter or a reference based supply. The 4.7 uF ceramic output capacitor is part of the specification, not an optional improvement.
What the published figures convert to
| Parameter | Published figure | What it means on a board |
|---|---|---|
| Input range | 2.3 V to 6.5 V | Runs from a 5 V rail or a single lithium cell |
| Output current | 1 A | Enough for a converter plus its digital core on one rail |
| Output noise | 5 uV rms from 100 Hz to 100 kHz | 1.67 ppm of 3 V, or 0.44 of an 18 bit code |
| Supply rejection | 60 dB at 100 kHz | A 100 mV switching ripple becomes 100 uV, so a 500 kHz converter front end is filtered by the regulator |
| Dropout | 42 mV at 500 mA | 0.042 W at 1 A, so a 3.3 V rail can feed it with margin |
| Transient response | 1.5 us for 1 mA to 500 mA | A digital core waking from sleep does not pull the analog rail out of regulation |
| Initial accuracy | Minus 0.5 to plus 1 percent | 30 mV on 3 V, which is why a reference is still needed for absolute accuracy |
| Accuracy over line, load and temperature | Plus or minus 1.5 percent | 45 mV total window across the industrial range |
| Quiescent current | 0.7 mA with no load | 3.5 mW at 5 V, small enough for a standby rail |
| Shutdown current | 0.25 uA | 2.19 mAh over a year, effectively nothing |
| Soft start | 1.0 ms with a 1 nF capacitor | Charging 4.7 uF to 3 V in 1 ms is 14.1 mA of inrush, well inside a 1 A part |
| Options | 17 fixed voltages plus adjustable from 1.2 V | One board family covers every rail from 1.2 V to 5 V |
| Package | 8 lead LFCSP 3 mm by 3 mm | The exposed pad is the heat path at 1 A |
Checks before accepting a cross reference
- Compare noise over the same bandwidth. A 5 uV figure from 100 Hz to 100 kHz is not comparable with a 10 Hz to 1 MHz figure.
- Check the dropout at the real load and temperature. A 42 mV figure at 500 mA may double at 1 A.
- Verify the minimum output capacitor. Parts that require 10 uF or more change the inrush and the board area.
- Confirm the soft start behaviour. A fixed start time can exceed the inrush budget of a hot swap front end.
- Ask for the transient response at the actual load step, since 1.5 us is quoted for a specific 500 mA step.
Where this part is used
Converter and reference rails, precision amplifier supplies, phase locked loop and voltage controlled oscillator bias, clocking devices, communications infrastructure, medical instruments and industrial measurement. It is the post regulator of choice after a buck converter when the analog rail cannot tolerate the switching ripple.
Questions buyers ask
Can it be paralleled? No. The part has no current sharing, so two units on one rail will fight. Use a larger regulator or split the loads.
What happens at 1 A in a 3 mm package? The thermal pad has to be connected to a copper area with thermal vias. At 3.3 V in and 3.0 V out the dissipation is only 0.3 W, which the package handles comfortably.
Does the fixed 3.0 V version need an external divider? No. The adjustable version does, and it is a separate order code with a different noise specification unless a feed forward capacitor is added.
Sourcing notes and next step
The regulator is listed with the power parts on the analog and mixed signal index, and rails that feed converters are covered in the ADC and DAC cross reference. Where a board has to change grade or package under allocation pressure, the parameter checks are in the drop in replacement verification guide. Tell us the input rail, the load profile and the noise limit and we will confirm the fixed voltage grade in stock.
Request Quote — In Stock, 100% New & Original, Full Warranty