Contact Us

ADM706RARZ

Brand: Analog Devices
Analog Devices ADM706RARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADM706RARZ — Analog & Mixed-Signal ICs | Superb Automation

ADM706RARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADM706RARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADM706RARZ: 2.63 V supervisor with a watchdog and a power fail input

The ADM706RARZ is a microprocessor supervisory circuit in an 8-lead narrow SOIC that holds a reset line low until the supply passes 2.63 V, keeps it low for 200 ms afterwards, and adds a watchdog and a 1.25 V power fail comparator. The R suffix is the threshold option, and it is the one that suits a 3.3 V rail.

Published values

ParameterValue
Reset threshold2.55 V minimum, 2.63 V typical, 2.70 V maximum
Reset timeout200 ms after the rail crosses the threshold
Quiescent current100 uA
Power fail input1.25 V comparator with a separate output
Watchdogseparate WDI input and WDO output
Reset validguaranteed with VCC as low as 1 V
Reset polarityactive low on the ADM706R, active high on the ADM706P
Package and range8-lead narrow SOIC, -40 C to +85 C

Putting 2.63 V on a 3.3 V rail

2.63 V is 20.3 percent below a 3.3 V nominal, so the monitor trips well outside the tolerance band of the rail it watches. At 3.3 V minus 5 percent, which is 3.135 V, the margin to the threshold is 505 mV, or 15.3 percent of nominal. That is a comfortable window: the supervisor does not fire on a legal rail, and it does fire before the logic is out of specification.

On a 2.5 V rail the same part never trips, because 2.63 V is above the rail. That sounds obvious and it is the most common ordering mistake in this family: the R threshold belongs to 3.3 V, the S to 3.0 V and the T to 3.3 V with tighter margins, and the letter has to be chosen against the rail, not against the reset pulse width.

The 200 ms reset and the watchdog

A 200 ms reset timeout is chosen so that a crystal oscillator and a processor phase locked loop have both started before the processor is released. A 1 MHz crystal reaches its specified accuracy in a few milliseconds, a 20 MHz one with a ceramic resonator takes longer, and a switching supply on the same rail may take 10 ms to reach regulation.

The watchdog is a separate timer with its own input and output. It is not wired to the reset output internally on this part in the way some supervisors do it: the WDO output has to be connected back to the manual reset input for a watchdog timeout to become a reset. A board that leaves WDO unconnected has a watchdog that only flags.

Power fail warning before the rail goes

The power fail comparator has a 1.25 V reference and its own input and output, so a divider from the unregulated input can warn the processor several milliseconds before the regulated rail starts to fall. That interval is what a processor needs to write its state to non volatile memory.

The warning time is set by the hold up capacitance and the load: at 100 mA and 1000 uF, a 1 V drop takes 10 ms, which is about right for a single page write. The divider has to be chosen so that the comparator crosses before the reset threshold, not after it.

Replacement checks

The P suffix is the active high reset output and the R, S and T suffixes are threshold options, so two parts that share the package can differ in both polarity and threshold. A replacement has to match the threshold against the rail, the polarity against the processor reset pin, and the watchdog wiring.

The pages below hold the power management cross reference and the verification sequence for a substitute.

The pages that answer this most often are the power management cross reference for the family alternatives, how to verify a drop in replacement for the acceptance test, and the ADI second source page for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Is the ADM706RARZ a direct replacement for the ADM706P? No. The P option has an active high reset output, the R option is active low, and the threshold value differs as well. The package is the same.

Can the watchdog be disabled? It can be left unused by tying WDI to a level that never transitions, which stops the watchdog from timing out. The output pin should still be treated as an output and not driven.